background image

13 — English

MAINTENANCE

WARNING:

The cutting attachment should never turn at idle. Turn 
the idle speed screw counterclockwise to reduce the 
idle RPM and stop the cutting attachment, or contact a 
service dealer for adjustment and discontinue use until 
the repair is made. Serious personal injury could result 
from the cutting attachment turning at idle.

HIGH ALTITUDE ENGINE OPERATION

Your engine is configured for operation below 2000 feet 
altitude at the factory. Your engine must be re-configured 
for operation above 2000 feet altitude. Operating the engine 
with the wrong engine configuration at a given altitude may 
increase its emissions, decrease fuel efficiency, degrade per-
formance and cause irreversible damage. Engines configured 
for high altitude operation cannot be operated in standard 
altitude conditions. A qualified service center should ensure 
that your engine is properly configured for your location.

INSTALLING LINE IN REEL-EASY

 STRING 

HEAD

See Figures 17 - 18.

Use .095 in./2.4 mm diameter monofilament line.

  Stop the engine and disconnect the spark plug wire.

  Cut one piece of line approximately 25 ft. in length.

  Rotate knob on string head until line on knob aligns with 

arrows on top of string head.

  Insert one end of line into eyelet located on either side 

of the string head and push until line comes out through 
eyelet on the other side. Continue to push line through 
the string head until the middle section of the line is inside 
the string head and line outside the string head is evenly 
divided on each side.

  While holding the string head in one hand with your other 

hand, rotate the knob clockwise on the string head to wind 
the line. Wind the line until approximately 8 in. remains 
protruding from the string head.

INSTALLING REEL-EASY

 STRING HEAD

See Figures 19 - 20.

  Stop the engine and disconnect the spark plug wire.

  Open the REEL-EASY

 string head by depressing the 

latches on each side. The contents of the string head are 
spring loaded, so keep your other hand over the string 
head cover while depressing the latches.

  Remove the string head cover, knob, and spool and set 

aside.

  Place the upper housing on the drive shaft. Make sure 

the string head is fully seated.

  Install the hex bolt into the opening on the drive shaft 

and secure using the hex-shaped opening in the knob 
to tighten. Turn counterclockwise to tighten.

 NOTE: Only use the knob to tighten the bolt. The use of 

other tools may allow overtightening of the bolt, which 
could damage the string head.

  If removed, replace the spring into the string head and 

push down to seat.

  Reinstall the spool. The spool should be placed so “This 

side out for straight shaft” is visible.

  Replace the knob in the spool.

  Replace the string head cover, aligning latches with 

openings in the string head. Press cover and string head 
together until both latches snap into openings securely.

  Install line as described in the operation section of this 

manual.

REPLACING THE EDGER BLADE

See Figures 21 - 23.

Replace blades when worn down to indicator hole on blade.
Use replacement blade model number AC04215.

  Stop the engine and disconnect the spark plug wire.

  Align the slot in the flange washer and gear case with the 

slot in the flange; place the holding pin through all three 
slots to secure in place.

  Using a 1/2 in. socket wrench, turn the blade nut clock-

wise to loosen.

  Remove the old blade from the edger shaft.

  Clean debris from the edger shaft and flange washers.

  Center the new blade on the flange washer, making sure 

the blade sits flat.

  Install the cupped washer with the hole off of the blade 

surface.

  Install the blade nut onto the edger shaft.

  Using a 1/2 inch socket wrench, turn the blade nut coun-

terclockwise onto the edger shaft and tighten securely.

  This replacement part is  available from the place of pur-

chase, or by calling customer service.

NOTE:  Always make sure the blade is correctly installed 
and securely fastened before each use.

ATTACHING THE STORAGE HANGER

See Figure 24.

There are two ways to hang the attachment for storage.

  To use the hanger cap, push in the button and place the 

hanger cap over the end of the attachment shaft. Slightly 
rotate the cap from side to side until the button locks into 
place.

  The secondary hole in the attachment shaft can be used 

for hanging purposes as well.

Summary of Contents for BM25TEC





































Reviews: