40794 v1
02/22/19
In-Wall
Wi-Fi
Smart Dimmer
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
RF Exposure:
A distance of 20 cm shall be maintained between the antenna and users, and the transmitter
module may not be co-located with any other transmitter or antenna.
Any changes or modifications not expressly approved by the party responsible for compliance
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy, and if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) This device may not cause interference, and (2) This device must accept any
interference, including interference that may cause undesired operation of the device.
This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment.
FCC
RISK OF FIRE
RISK OF ELECTRICAL SHOCK
RISK OF BURNS
CONTROLLING APPLIANCES
CAUTION:
TO REDUCE THE RISK OF OVERHEATING AND
POSSIBLE DAMAGE TO OTHER EQUIPMENT, DO NOT INSTALL
TO CONTROL A RECEPTACLE, MOTOR-OPERATED APPLIANCE,
FLUORESCENT LIGHTING FIXTURE, OR A TRANSFORMER-
SUPPLIED APPLIANCE.
• ONLY USE TO CONTROL INCANDESCENT OR DIMMABLE CFL/
LED BULBS
• DO NOT EXCEED RATINGS
• DO NOT USE TO CONTROL ANY DEVICE WHERE
UNINTENDED OPERATION COULD CAUSE UNSAFE
CONDITIONS (HEAT LAMP, SUN LAMP, ETC.)
• FOR INDOOR USE ONLY
WARNING
WARNING — SHOCK HAZARD
Turn OFF the power to the branch circuit for the dimmer and lighting fixture at the service panel. All wiring connections
must be made with the power OFF to avoid personal injury and/or damage to the dimmer. This device is intended for
installation in accordance with the National Electric Code and local regulations in the United States or the Canadian
Electrical Code and local regulations in Canada. If you are unsure or uncomfortable about performing this installation,
consult a qualified electrician.
MADE IN CHINA
GE IS A TRADEMARK OF GENERAL ELECTRIC COMPANY AND IS
UNDER LICENSE BY JASCO PRODUCTS COMPANY LLC,
10 E. MEMORIAL RD., OKLAHOMA CITY, OK 73114.
This Jasco product comes with a 1-year limited warranty.
Visit www.byjasco.com for warranty details.
Questions? Contact our U.S.-based Consumer Care at
1-800-654-8483 between 7AM—8PM CST.
SPECIFICATIONS
Power: 120VAC, 60Hz
Signal (Frequency): 908.4/916MHz
Maximum loads: 600W, 2-gang 500W or 3-gang
400W incandescent, 150W or 2A CFL/LED
Operating temperature range: 32-104° F (0-40° C)
For indoor use only.
Specifications subject to change without notice
due to continuing product improvement.
Getting to know your new Wi-Fi Smart Dimmer
• Turn ON/OFF manually or through the myTouchSmart app
• Compatible with Amazon Alexa and Google Home
• May be used in single-pole installation or 3-way
wiring configurations
• Compatible with all incandescent and most dimmable
CFL/LED bulbs
• Interchangeable rocker paddle — white & light
almond included
• Uses a standard, decorative-size wallplate for single-gang
installations (wallplate not included)
• Screw terminal installation — requires wiring connections
for line (hot), load, neutral and ground. Traveler wire
required for 3-way installation
Required tools
IMPORTANT!
The fixture controlled by the Wi-Fi Smart Dimmer must not
exceed 600W (incandescent); 150W dimmable CFL/LED.
1.
3-way dimmer wiring
IMPORTANT!
3 -way switches can be wired in different
ways. These instructions explain the most
common method. If you have difficulty with
the instructions or your home wiring, contact a
licensed electrician for assistance.
1. Shut off power to the circuit breaker or fuse box.
IMPORTANT!
Verify power to switch
is OFF before continuing.
2. Remove line side wallplate.
3. Remove mounting screws to
existing line side switch.
4. Carefully remove switch from switch
box. DO NOT disconnect wires yet.
5. Identify black wire (line) connected
to circuit breaker, attached to
black screw. Label wire “line.”
6. Identify red wire (typically) also
connected to load side, attached to
other brass screw. Label “traveler 1.”
7. Identify black wire connected to load side,
attached to brass screw. Label wire “traveler 2.”
Single-switch wiring
Removing existing switch
Before installation, you may wish to change
the paddle color to match your wallplate
or décor. Please return to section 3.
A. Shut off power to the circuit at
circuit breaker or fuse box.
IMPORTANT!
Verify power to switch box is OFF
before continuing.
B. Remove wallplate.
C. Remove the switch mounting screws.
D. Carefully remove the switch from the
switch box. DO NOT disconnect the wires.
Up to five screw terminals on the switch are
marked:
a. GROUND — Green/Bare.
b. LOAD — Black (connected to lighting).
c. LINE (Hot) — Black (connected to power).
d. TRAVELER — Red.
e. NEUTRAL — White.
Match these screw terminals to the wires
connected to the existing switch.
E. Disconnect the wires from the existing
switch. Label wires according to the
previous terminal connection.
Installation
Wire strip length:
Strip insulation for attachment 5/8in. (16mm).
UL specifies the tightening torque for
the screws is 12lbf-in (14Kgf-cm).
F. Connect the green or bare copper
ground wire to the ground terminal.
I. Connect the black wire from the
light to the load terminal.
II. Connect the black wire from the electrical
service panel (hot) to the line terminal.
III. Connect the white wire to the neutral
terminal. Use a jumper wire if needed.
Often, the neutral wire can be found in the
back of the switch box. There may be
several neutral wires bound together with
a wire nut.
Note:
The traveler terminal is only used for
3-way installations.
IV. Insert dimmer into the switch box being
careful not to pinch or crush wires.
G. Secure the switch to the box
using the supplied screws.
H. Reapply power to the circuit at fuse box or
circuit breaker. The blue indicator light under
the ON/OFF paddle should blink rapidly.
If the blue light is not blinking, first ensure
the air gap switch is in ON position (right).
If the blue light is still not blinking, turn off
the breaker, verify there is no power to the
Wi-Fi dimmer, switch the wires in the line
and load terminals, and tighten the screws.
Mount the wallplate and reapply power to
the circuit at fuse box or circuit breaker.
A
B
C
C
A
D
B
E
D
E
G
H
Line
Ground
Line side (hot)
Load side
H
H
H
H
Load
C
C
In a typical 3-way application, there are two 3-way switches. The switch on the line (hot)
side has the common terminal tied to 120VAC. The switch on the load side has the
common terminal tied to the load the switches turn ON/OFF.
5.
Figure 2 - Line side after
Figure 1
-
Line side switch before
2
1
3
Line
H
H
4
Ground
2
5
4
Ground
Line
H
H
1. Black wire/black screw - line
2. Red wire/brass screw - traveler 1
3. Black wire/brass screw - traveler 2
4. Copper wire/green screw - ground
C
C
1. Black wire (line) to wire nut
2. Red wire (traveler 1) to brass screw
3. Black wire (traveler 2) to wire nut
4. Green/copper wire - ground
5. White jumper to wire nut/black screw
1
3
2
Typical wiring schematic for 3-way Installation
TRAVELER
LOAD
LINE
NEUTRAL
Load
Figure 4 - Load side switch after (Wi-Fi)
2
4
3
1
5
Figure 3
- Load side switch before
3
1
2
H
H
Load
4
GROUND
1. Black wire/black screw - load
2. Red wire/brass screw - traveler 1
3. Black wire/brass screw - traveler 2
4. Green/copper wire - ground
C
Load
Traveler 2
Neutral
Traveler 1
Ground
A.
Ground
(Green/Bare)
B.
Load
(Black)
C.
Line
(Black)
D.
Traveler
(Red/Other)
E.
Neutral
(White)
F.
Air Gap Switch
—
Removes power
from dimmer.
G.
Top rocker
— Press &
release to turn dimmer
ON, press & hold
increases brightness
Press & release to turn
device ON. Press &
hold for 10 seconds
to reset Wi-Fi device
to factory specs
H.
Bottom rocker
— Press
& release to turn dimmer
OFF, press & hold to dim
H
G
E
C
B
A
D
2.
3.
To change the paddle
This step is optional.
Before installation,
you may want to
change the color of the
paddle to match your
wallplate or décor.
1. Insert a small, flat-
blade screwdriver into
either groove at the
top of the paddle, and
apply gentle pressure
to remove the paddle.
2. Align the new paddle
with the bottom of
the Wi-Fi device and
press it into place.
OR
OR
4.
From breaker box
Out to light (load)
LOAD
NEUTRAL
GROUND
LINE
TRAVELER
From breaker box
Insert wires into holes, do not
wrap wires around screws.
Do not remove screws.
F
TOP
READ IT
OR
WATCH IT
Read instructions or watch easy-to-follow
video. Scan QR code or visit goo.gl/NX4SRq
Prepare line side for new 3-way connection
1. Disconnect black wire marked “line” from
the black screw and the other black wire
labeled “traveler 2” from brass screw.
2. Use the provided wire nut to connect
the two black wires with one of the
included white jumper wires.
3. Connect the free end of the white jumper wire
to the black screw (hot) on the existing switch.
4. Carefully replace the switch back into
the switch box. Ensure the wires are
not pinched or crushed. Secure the
switch using the mounting screws.
Installing the Wi-Fi dimmer on the load side
1. Remove load side wallplate.
2. Remove existing switch from load side
switch box. DO NOT disconnect wires yet.
3. Identify black wire connected to the load (light
fixture) attached to black screw. Label as “load.”
4. Identify red wire from line side, attached
to bass screw. Label wire “traveler 1.”
5. Identify black wire coming from line
side. Label wire “traveler 2.”
6. Locate neutral wires inside switch box.
Connect the other included white jumper wire
to neutral wire bundle. Label wire “neutral.”
7. Disconnect black wire labeled “load” and
connect to load terminal on Wi-Fi dimmer.
8. Disconnect red wire labeled “traveler 1” and
connect to traveler terminal on Wi-Fi terminal.
9. Disconnect black wire labeled “traveler 2” and
connect to line terminal on Wi-Fi dimmer.
10. Connect free end of white jumper wire
to neutral terminal on Wi-Fi dimmer.
11. Disconnect green or copper wire and connect
to ground terminal on Wi-Fi dimmer.
12. Carefully place the Wi-Fi dimmer back
into the switch box. Ensure the wires
are not pinched or crushed. Secure in
place using the mounting screws.
13. Turn on circuit breaker or fuse box.
14. Verify the blue indicator LED on Wi-Fi dimmer
blinks rapidly. If the blue light is not blinking,
first ensure the air gap switch is in ON position
(right). If the blue light is still not blinking, turn
off the breaker, verify there is no power to
the Wi-Fi dimmer, switch the wires in the line
and load terminals, and tighten the screws.
Mount the wallplate and reapply power to
the circuit at fuse box or circuit breaker.
Line side
Load side
F
Insert wires into holes, do not
wrap wires around screws.
Do not remove screws.
Caution:
could void the users authority to operate this equipment
This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
MTS5406, MTS5407
FCC ID: QOB-MTS5406
