Black+Decker JC450, Original Instructions Manual

Page: 4 / 16

4
ENGLISH (Original instructions)
• If the power supply cord or mains plug is damaged or
defective it must be repaired by an authorised repair
agent in order to avoid a hazard. Do not cut the power
supply cord and do not attempt to repair it yourself.
• Never attempt to remove or replace any parts other than
those specified in this manual.
Electrical safety
This product must be earthed. Always check
that the power supply corresponds to the
voltage on the rating plate.
• Power plugs must match the outlet. Never modify the
plug in any way. Do not use any adapter plugs with
earthed (Class 1) appliances. Unmodified plugs and
matching outlets will reduce the risk of electric shock.
Extension cables & Class 1 product
• A 3-core cable must be used as your appliance is
earthed and of Class 1 construction.
• Up to 30m (100ft) can be used without loss of power.
To avoid the risk of electric shock, do not
immerse the cord, plug or appliance in water or
other liquid.
• If the supply cord is damaged, it must be replaced by the
manufacturer or an authorized BLACK+DECKER
Service Center in order to avoid a hazard.
Features
1. Lid
2. Spout
3. Water level guage
4. Body
5. Power base
6. Switch
7. Handle
8. Lid release button
Before first use
• Remove all packaging from the appliance.
• Clean the appliance before first use.
• Fill the kettle with cold water to the maximum fill mark.
Do not over fill. Fill as described below.
• Close the lid (1). Boil the water as described below.
• Discard the boiled water and repeat the procedure.
Use
Warning! Always place the appliance on a flat, clean and
non-slip surface before operating it.
Warning! Always allow the product and contents to cool
before opening the lid / re-filling.
Warning! Always check the water level while using the
appliance.
Never use the appliance without sufficient water.
Warning! Steam may escape from the spout.
Warning! This Kettle must only be used with the Kettle base
provided.
• Place the kettle base (5) on a suitable surface.
• Take the kettle to a water outlet. Open the lid (1) by
pressing the lid release (8).
• Fill the kettle with cold water to the desired level.
• To prevent dry-boiling fill to at least 250 ml (one cup).
• Do not fill the kettle beyond the maximum fill mark. If the
kettle is overfilled, boiling water may be ejected from the
pouring spout (2).
• Close the lid (1) and make sure it snaps into place.
• Place the kettle on the power base (5).
• Insert the plug into a suitable electrical outlet and push
the on/off switch (6) to the on position (I).
• The power on indicator will light.
• The water will start boiling, making a rumbling noise. Do
not open the lid when the water is boiling.
• As soon as the water has boiled, the appliance will switch
off and the power on indicator will go out.
• Always ensure the Kettle has turned off before lifting it
from the Kettle base.
• To switch the appliance off during boiling, push the switch
(6) the off position (O).
• If you do not want to use the boiled water immediately,
the kettle may be left on the base. If you want to bring the
water back to boil after a while, push the on / off switch
(6) to on again.
Pouring boiling water
• Make sure the appliance is switched off.
• Take the kettle off the base.
• To avoid scalding, tilt the kettle slowly to pour the boiled
water.
• After pouring, place the kettle back on the base and
remove the plug from the socket.
Cleaning and Maintenance
Before performing any maintenance:
• Switch off and disconnect from the mains supply.
• Wait for the appliance to completely cool down.
Warning! Do not immerse the appliance, the base, the cord
set or the plug in water or any other liquid.
• Wipe the exterior with a damp cloth.
• Do not use scouring pads.
• If necessary, use a mild detergent to remove spots.
• Do not use any abrasive or solvent based cleaner.
• Do not immerse the appliance or power base in water or
any other liquid.