Black+Decker FX1073-B5, Original Instructions Manual

Page: 5 / 24

5. When you use the disc holder with one of the discs, add
the ingredients through the feeding chute and push
them down with the pusher
6. Select the speed setting that corresponds with the
accessory you choose. See the appropriate section
below.
7. When you have finished processing, turn the speed
selector to 0.
Feeding tube and pusher
- Use the feeding chute to add liquid and/or solid
ingredients.
- Use the pusher to push solid ingredients down the
feeding chute.
Tip : You can also use the pusher to close the feeding chute.
This prevents ingredients from escaping through the feeding
chute.
Chopping blade
You can use the chopping blade to chop, mix, blend or puree
ingredients.
1. Remove the protective cover from the blade. The cutting
edges are very sharp. Do not touch them.
2. Put the drive shaft in the bowl.
3. Put the chopping blade on the drive shaft in the bowl
4. Put the ingredients in the bowl. Pre-cut large pieces of
food into pieces of approx. 3 x 3 x 3cm
Note : Always put the drive shaft with the chopping blade in
the bowl before you add the ingredients
5. Put the lid on the bowl. Turn the lid clockwise to fix it
(‘click’).
Note : Make sure the projection on the lid locks into the slot
of the bowl handle.
6. Put the pusher in the feeding chute.
7. Select the speed that corresponds with the accessory.
8. When you have finished processing, turn the speed
selector to 0 and unplug the appliance.
Tips
- When you chop onions, turn the speed selector to P
(pulse position) a few times to prevent the onions from
becoming too finely chopped.
5
ENGLISH
(Original instructions)
- Do not let the appliance run too long when you chop
(hard) cheese or chocolate. Otherwise these ingredients
become too hot, start to melt and turn lumpy.
- Do not use the chopping blade to chop very hard
ingredients like coffee beans, turmeric, nutmeg and ice
cubes, as this may cause the blade to get blunt.
- If food sticks to the blade or to the wall of the bowl, switch
off the appliance and un plug it. Then use a spatula to
remove the food from the blade or from the wall of the
bowl.
Kneading blade
You can use the kneading blade to knead yeast dough for
bread and pizzas.
1. Put the drive shaft in the bowl.
2. Put the kneading blade on the drive shaft.
Note : Always put the drive shaft with the kneading blade in
the bowl before you add the ingredients.
3. Put the ingredients in the bowl.
4. Put the lid on the bowl. Turn the lid clockwise to fix it
(‘click’).
Note: Make sure the projection on the lid locks into the slot of
the bowl handle.
5. Put the pusher in the feeding chute.
6. Select the speed that corresponds with the accessory.
7. When you have finished processing, turn the speed
selector to 0 and unplug the appliance.
Slicing, shredding and grating discs
Never process hard ingredients like ice cubes with the discs.
The cutting edges of the discs are very sharp. Do not touch
them
1. Put the drive shaft in the bowl.
2. Place the shredding, slicing or grating disc in the disc
holder
- Place the opening of the disc over the shaft of the disc
holder.
- Push the opening of the disc over the projection on the
disc holder.
- Press the disc onto the disc holder unit it locks in the
position with a click
3. Place the disc holder with disc on the drive shaft.
4. Put the lid on the bowl. Turn the lid clockwise to fix it
(‘click’).
Note : Make sure the projection on the lid locks into the slot of
the bowl handle.
5. Put the ingredients in the feeding chute.
Accessory Preferred speed setting
Shredding, slicing & grating 1
discs
Kneading blade 1
Emulsifying disc 1
Blender 2 & Pulse
Chopper 2 & Pulse
Grinder 2