![background image](http://html1.mh-extra.com/html/black-decker-1/bdgs36/bdgs36_original-instructions-manual_2765854010.webp)
10
ENGLISH
(Original instructions)
Chargers
Your charger has been designed for a
specific voltage. Always check that the
mains voltage corresponds to the voltage
on the rating plate.
Warning!
Never attempt to replace the
charger unit with a regular mains plug.
u
Use your BLACK+DECKER charger
only to charge the battery in the tool
with which it was supplied. Other
batteries could burst, causing personal
injury and damage.
u
Never attempt to charge non-
rechargeable batteries.
u
If the supply cord is damaged, it must
be replaced by the manufacturer or an
authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
u
Do not expose the charger to water.
u
Do not open the charger.
u
Do not probe the charger.
u
The appliance/tool/battery must be
placed in a well ventilated area when
charging.
The charger is intended for
indoor use only.
Read the instruction manual
before use.
Electrical safety
Your charger is double insulated;
therefore no earth wire is required.
Always check that the mains
voltage corresponds to the voltage
on the rating plate.
u
If the supply cord is damaged, it must
be replaced by the manufacturer or an
authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
u
Warning!
Never attempt to replace the
charger unit with a regular mains plug.
Features
1. On/off switch
2. Lock-off button
3. Blade release button
4. Shear blade
5. Charging indicator
Assembly
Warning!
Avoid accidentally switching the tool on during
assembly.
Fitting the wall mount to the wall (fig. A & B)
The wall mount can be fitted to the wall to provide a
convenient storage and charging point for the tool.
u
Drive the screws in the wall through the holes in the
crevices of wall mount.
u
Place the tool on the wall mount.
u
Plug in the charger making sure the charging indicator (6)
lights up (fig. A).
Warning!
Avoid damaging the power cord when mounting the
wall mount to the wall.
Removing the charger plug from the wall mount
(fig. C)
The tool can be charged without using the wall mount. The
charger plug can be connected to the tool directly.
u
Remove the screws from the back of the wall mount.
u
Slide the back part (8) from the front part (9) to open the
wall mount.
u
Remove the charger plug from the wall mount.
Fitting and removing the blade (fig. D & E)
The shear blade (4) has been designed for trimming grass
and weeds.
u
Remove the blade cover.
u
Push and hold the blade release button (3) in the direction
of the arrow (fig. D1).
u
Slide the blade cover (10) backward and lift off (fig. D2).
u
Lower the blade onto the pins.
u
While holding the blade onto the pins (fig. E1), replace the
blade cover (10) and slide it forward (fig. E2).
Summary of Contents for BDGS36
