Page 10
SET UP & USE
PREPARE THE WINDOW
through the condenser, for heat removal. The rear of the unit must be outdoors, not inside
a building or garage.
MOUNTING HARDWARE
PREPARE AIR CONDITIONER
B: Remove top rail from the packaging material as shown in Fig. A.
Use 2 people to lift.
TOP RAIL HARDWARE
Screws
(7)
Lock Frame
(2)
Sash Lock
(1)
Window sash
seal foam
(1)
3/8 Screws
(4)
Top Rail
(1)
Packaging
Fig.A
Top Rail
R1 hardware
(2)
R1 hardware(for
>
)
10000Btu/h models
only
R1 hardware
(for <
)
10000
Btu/h models
only
Lock Frame
(2)
(For Wooden
windows)
(For Vinyl-Clad
windows)
(on some models)
(10 *3/4 *1/12 )
Weather stripping
(5)
3/ 4 (or 1/
Screws
(7)
2 )
Lock Frame
(2)
Sash Lock
(1)
Window sash
seal foam
(1)
3/8 Screws
(4)
Top Rail
(1)
Packaging
Top Rail
Lock Frame
(2)
(For Wooden
windows)
(For Vinyl-Clad
windows)
(on some models)
(10 *3/4 *1/12 )
Weather stripping
(5)
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions: 1) This device may not cause harmful interference, and 2) This device must accept any
interference received, including interference that may cause undesired operation. This equipment has
been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that the interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures: a) Reorient or relocate the receiving antenna.
b) Increase the separation between the equipment and the receiver. c) Connect the equipment into
an outlet different from that which the receiver is connected. d) Consult the dealer or an experienced
radio/TV technician for help.
Fig. A
3/ 4 (or 1/
Screws
(7)
2 )
Lock Frame
(2)
Sash Lock
(1)
W
s
(
3/8 Screws
(4)
Top Rail
(1)
Packaging
Fig.A
Top Rail
R1 ha
(2
R1 hardware
>
)
10000Btu/h m
only
R1 ha
(for <
)
1
Btu/h m
only
Lock Frame
(2)
(For Wooden
windows)
(For Vinyl-Clad
windows)
(on some models)
(10 *3/4 *
Weather stripping
(5
3/ 4 (or 1/
Screws
(7)
2 )
Lock Frame
(2)
Sash Lock
(1)
W
s
(
3/8 Screws
(4)
Top Rail
(1)
Packaging
Fig.A
Top Rail
R1 ha
(
R1 hardwar
>
)
10000Btu/
only
R1 ha
(for <
)
Btu/h m
only
Lock Frame
(2)
(For Wooden
windows)
(For Vinyl-Clad
windows)
(on some models)
(10 *3/4 *
Weather stripping
(5
3/ 4 (or 1/
Screws
(7)
2 )
Lock Frame
(2)
Sash Lo
(1)
3/8 Screws
(4)
Top Rail
(1)
Packaging
Fig.A
Top Rail
R
(
R1 hard
>
)
10000B
only
R
(f
B
o
Lock Frame
(2)
(For Wooden
windows)
(For Vinyl-Clad
windows)
(on some models)
(1
Weather stripping
(
3/4” (or 1/2”)
