Black Box MDS931AE-10BT User Manual Download Page 20

Page: 20 / 30

User Manual

5.5.2 CONFIG command

The CONFIG command informs the user about the configured parameters.

NTU_CM>CONFIG

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

xDSL

Line

Rate,kbit/s: 2320

Master/Slave:

Master

Adaptive

mode:

Ethernet

Speed:

AUTO

Duplex

mode:

AUTO

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

NTU_CM>

5.5.3 RESET command

The RESET command restarts the modem.

NTU_CM>RESET

01:55:02 system reset

5.5.4 MASTER command

The MASTER command sets the modem either in the maser or slave modes.

NTU_CM>MASTER ON

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

xDSL

Line

Rate,kbit/s: 2320

Master/Slave:

Master

Adaptive

mode:

Ethernet

Speed:

AUTO

Duplex

mode:

AUTO

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

NTU_CM>MASTER OFF

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

xDSL

Line

Rate,kbit/s: 2320

Master/Slave:

Slave

Adaptive

mode:

Ethernet

Speed:

AUTO

Duplex

mode:

AUTO

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

NTU_CM>

Page 20 of 30

Summary of Contents for MDS931AE-10BT































Search results

Summary of Contents for MDS931AE-10BT

Reviews:

Related manuals for MDS931AE-10BT

Brands by name

Popular brands

Black Box MDS931AE-10BT, User Manual

Search results

Summary of Contents for MDS931AE-10BT

Reviews:

Related manuals for MDS931AE-10BT

Brands by name

Popular brands