6
TO REDUCE THE RISK OF KICKBACK
.HHSDILUPJULSRQVDZZLWKERWKKDQGVDWDOO
times.
6WD\DOHUW²H[HUFLVHFRQWURO
6XSSRUWORQJRYHUKDQJLQJPDWHULDOV$V
WKHPDWHULDOLVFXWDQGZHDNHQVLWZLOOVDJ
causing a pinched blade.
6XSSRUWODUJHSDQHOVDVVKRZQ
Fig. 1
).
0DWHULDOVXSSRUWHGRQO\DWWKHHQGV
Fig. 2
)
will lead to blade pinching.
$YRLGVDZLQJRYHUKHDG0DWHULDOFDQVDJ
and will pinch blade.
,QVXUHWKDWWKHPDWHULDOWREHFXWLVFODPSHG
figure 3
) and solidly supported and
EDODQFHGRQDVWURQJVWDEOHDQGOHYHOZRUN
VXUIDFH6XSSRUWWKHZRUNVRWKDWWKHZLGH
portion of the saw shoe is on the portion
of the material that doesn’t fall after the cut
is made. Never hold cut off piece by hand
figure 4
)
.HHSEODGHVVKDUSDQGFOHDQ
8VHIHQFHRUVWUDLJKWHGJHJXLGHZKHQ
ripping. Be careful as the cut off strip can
sag or twist, closing the cut and pinching the
EODGHOHDGLQJWR.,&.%$&.
'RQҋWIRUFHWRRO:RRGYDULDEOHVVXFKDV
NQRWVKDUGQHVVWRXJKQHVVZHWQHVV
pressure treated and freshly cut green
lumber can heavily load the saw which can
lead to stalling. Push the saw slower when this
occurs.
'RQҋWUHPRYHVDZIURPZRUNGXULQJDFXW
while the blade is moving.
$OORZVDZWRUHDFKIXOOVSHHGEHIRUHEODGH
contacts material to be cut. Starting the saw
ZLWKWKHEODGHDJDLQVWWKHZRUNRUSXVKHG
forward into cut can lead to stalling or sudden
EDFNZDUGPRYHPHQWRIVDZ
1HYHUDWWHPSWWROLIWVDZZKHQPDNLQJDEHYHO
cut. This leads to blade binding and stalling.
$OZD\VVHFXUHZRUNWRSUHYHQWZRUNSLHFH
movement during cut.
'RQRWWU\WRIRUFHVDZEDFNRQOLQHLI\RXU
cut begins to go off line. This can cause
.,&.%$&.6WRSVDZDQGDOORZEODGHWR
FRDVWGRZQWRDVWRS:LWKGUDZIURPFXWDQG
start a new cut on the line.
6HWGHSWKDGMXVWPHQWRIVDZVXFKWKDW
one tooth of the blade projects below the
ZRUNSLHFHDVVKRZQLQ
(figure 7).
'RQRWEDFNXSDURWDWLQJEODGHLQWKHFXW
7ZLVWLQJWKHVDZFDQFDXVHWKHEDFNHGJHRI
the blade to dig into the material, climb out of
WKHZRUNDQGUXQEDFNWRZDUGWKHRSHUDWRU
$YRLGFXWWLQJQDLOV,QVSHFWIRUDQGUHPRYHDOO
nails from lumber before cutting.
MOTOR
Be sure your power supply agrees with
QDPHSODWHPDUNLQJ9ROWV$&PHDQV
your tool will operate on standard 60 Hz
KRXVHKROGSRZHU'RQRWRSHUDWH$&WRROV
RQ'&$UDWLQJRIYROWV$&'&PHDQV
that your tool will operate on standard 60 Hz
$&RU'&SRZHU7KLVLQIRUPDWLRQLVSULQWHG
on the nameplate. Lower voltage will cause
ORVVRISRZHUDQGFDQUHVXOWLQRYHUKHDWLQJ
All
Black & Decker
WRROVDUHIDFWRU\WHVWHG
LIWKLVWRROGRHVQRWRSHUDWHFKHFNWKHSRZHU
VXSSO\7KLVWRROLV$&RQO\
INTENDED USE
This circular saw is designed for wood
cutting applications.
Do not
use water feed
attachments with this saw.
Do not
use
abrasive wheels or blades.
Do not
use under
wet conditions or in presence of flammable
liquids or gases.
SAVE THESE INSTRUCTIONS
3
4
1
2
