3UHYHQWVSLQGOHURWDWLRQE\HQJDJLQJ
the spanner wrench into the holes of
the outer washer.
Securely tighten the blade retaining
screw by holding the spanner wrench
DQGWXUQLQJKH[ZUHQFKFORFNZLVHWR
tighten the blade retaining screw.
REMOVING THE BLADE
7RSUHYHQWVSLQGOHURWDWLRQHQJDJHWKH
SURWUXVLRQVRIWKHVSDQQHUZHQFK
LQWRWKHKROHVLQWKHRXWHUZDVKHU
Loosen and remove the blade retaining
VFUHZE\WXUQLQJLWFRXQWHU
FORFNZLVHXVLQJWKHKH[ZUHQFK
5HPRYHWKHRXWHUZDVKHU
5HPRYHWKHVDZEODGH
WARNING:
7RUHGXFHWKHULVNRI
serious personal injury, read, understand
and follow all important safety warnings
and instructions prior to using tool.
GENERAL CUTS (IMPORTANT:
READ SAFETY WARNINGS AND
INSTRUCTIONS. )
GUARD AGAINST KICKBACK
:LWKXQLWXQSOXJJHGIROORZDOODVVHPEO\
adjustment and set up instructions.
0DNHVXUHORZHUJXDUGRSHUDWHV6HOHFW
the proper blade for the material to be cut.
0HDVXUHDQGPDUNZRUNIRUFXWWLQJ
6XSSRUWDQGVHFXUHZRUNSURSHUO\6HH
Safety Rules and Instructions).
8
8VHDSSURSULDWHDQGUHTXLUHGVDIHW\
HTXLSPHQW6HH6DIHW\5XOHV
6HFXUHDQGPDLQWDLQZRUNDUHD6HH
Safety Rules).
:LWKSOXJLQVHUWHGDQGJXDUGFORVHG
PDNHVXUHVZLWFKWXUQVVDZRQDQGRII
WARNING:
It is important to support
WKHZRUNSURSHUO\DQGWRKROGWKHVDZ
firmly to prevent loss of control which
could cause personal injury.
Figure 3
illustrates recommended hand position.
OPERATION
SWITCH
7RRSHUDWHWKHWRROGHSUHVVWKHWULJJHU
VZLWFK7KHWRROZLOOFRQWLQXHWRUXQ
as long as the trigger is depressed.
7RWXUQWKHWRRORIIUHOHDVHWKHWULJJHU
VZLWFK7KHUHLVQRSURYLVLRQIRU
ORFNLQJWKHWRRORQDQGWKHVZLWFK
VKRXOGQHYHUEHORFNHGRQE\DQ\RWKHU
means.
SAWING
WARNING:
7RUHGXFHWKHULVNRI
serious personal injury,always hold the
tool with both hands.
/HWWKHEODGHUXQIUHHO\IRUDIHZ
seconds before starting the cut.
$SSO\RQO\DJHQWOHSUHVVXUHWRWKHWRRO
while performing the cut.
:RUNZLWKWKHVKRHSUHVVHGDJDLQVW
WKHZRUNSLHFH
HINTS FOR OPTIMUM USE
$VVRPHVSOLQWHULQJDORQJWKHOLQHRI
FXWRQWKHWRSVLGHRIWKHZRUNSLHFH
cannot be avoided, cut on the side
where splintering is acceptable.
:KHUHVSOLQWHULQJLVWREHPLQLPL]HG
e.g. when cutting laminates, clamp a
piece of plywood onto the top of the
ZRUNSLHFH
POCKET CUTTING (FIG.11)
WARNING:
Never tie the blade guard
in a raised position. Never move the saw
EDFNZDUGVZKHQSRFNHWFXWWLQJ7KLV
may cause the unit to raise up off the
ZRUNVXUIDFHZKLFKFRXOGFDXVHLQMXU\
$SRFNHWFXWLVRQHWKDWLVPDGHLQD
floor, wall, or other flat surface.
$GMXVWWKHVDZIRRWSODWHVRWKHEODGH
cuts at desired depth.
7LOWWKHVDZIRUZDUGDQGUHVWIURQWRI
the foot plate on material to be cut.
8VLQJWKHUHWUDFWLQJOHYHUUHWUDFWORZHU
10
11
10
8
16
9
8
10
11
