7
ENGLISH
(Original instructions)
Use
@
WARNING!
Let the tool work at its own pace. Do not
overload.
@
WARNING!
Before drilling into walls, floors or
ceilings, check forthe location of wiring and pipes.
Selecting the direction of rotation (fig. D)
For drilling and for tightening screws, use forward
(clockwise) rotation. For loosening screws or removing a
jammed drill bit, use reverse (counter clockwise) rotation.
u
To select forward rotation, push the forward/reverse
switch (3) to the left position.
u
To select reverse rotation, push the forward/reverse
button to the right.
@
WARNING!
Never change the direction of rotation
while the motor is running.
Selecting the drilling mode (fig. D)
u
To select a drilling mode, push button 4a and rotate the
selector to the required setting.
u
For Rotary hammering in masonry and concrete, set the
drilling mode selector (4) to the
qr
position.
u
For drilling in steel, wood and plastics or for screw driving
drilling mode selector (4) to the
r
position.
u
For chiselling mode set the drilling mode selector (4) to
the
q
position.
Setting the drilling depth (fig. A)
u
Slacken the side handle (6) by turning the knob (6a)
counter clockwise.
u
Set the depth guage (7) to the desired position. The
maximum drilling depth is equal to the distance between
the tip of the drill bit and the front end of the depth guage.
u
Tighten the side handle by turning the knob (6c) clockwise.
Switching on and off
u
To switch the tool on, press the variable speed
switch (1). The tool speed depends on how far you
press the switch. As a general rule, use low speeds
for large diameter drill bits and high speeds for smaller
diameter drill bits.
u
For continuous operation, press the lock-on button (2)
and release the variable speed switch. The lock on button
is available only at full speed in forward mode.
In the reverse mode, the lock on button is not available.
u
To switch the tool off, release the variable speed switch.
To switch the tool off when in continuous operation,
press the variable speed switch again and release it.
Always hold the tool as shown in figure G.
Accessories
The performance of your tool depends on the accessory used.
BLACK+DECKER accessories are engineered to high quality
standards and designed to enhance the performance of your
tool. By using these accessories you will get the very best
from your tool.
Maintenance
Your BLACK+DECKER corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
@
WARNING!
Before performing any maintenance on
corded / cordless power tools:
u
Switch off and unplug the appliance/tool.
u
Or switch off and remove the battery from the appliance/
tool if the appliance/tool has a separate battery pack.
u
Or run the battery down completely if it is integral and then
switch off.
u
Unplug the charger before cleaning it. Your charger does
not require any maintenance apart from regular cleaning.
u
Regularly clean the ventilation slots in your appliance/tool/
charger using a soft brush or dry cloth.
u
Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
u
Regularly open the chuck and tap it to remove any dust
from the interior (when fitted).
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
u
Safely dispose of the old plug.
u
Connect the brown lead to the live terminal in the new
plug.
u
Connect the blue lead to the neutral terminal.
@
WARNING!
No connection is to be made to the earth
terminal. Follow the fitting instructions supplied with
good quality plugs. Recommended fuse: 5 A.
Protecting the environment
Z
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be recovered or
recycled, reducing demand for raw materials.
Please recycle electrical products and batteries according to local
provisions. Further information is available at www.2helpU.com
Technical data
BEHS01
Input voltage
V
AC
230
Power input
W
650
No load speed
min
-1
0 - 1600
