background image

(40,5 °C). (4) If the receptacle and temperature are OK, and you do not get proper
charging, take or send the tool and charger to your local Black & Decker service 
center. See "Tools Electric"’ in yellow pages.

5. The drill should be recharged when it fails to produce sufficient power on the jobs which

previously were done easily. DO NOT CONTINUE to use the drill with its battery in a
depleted condition.

6. To prolong battery life, avoid leaving the tool on charge for more than 2 days. Although

overcharging is not a safety concern, it can significantly reduce overall battery life.

7. Since the unit is designed for cordless applications, use of the unit while plugged in is of

no benefit. Batteries will still become depleted.

8. Unplug your tool’s charger from the power supply before disconnecting the charger from

the tool. Under certain conditions, with the charger plugged in to the power supply, the
exposed charging plug can be shorted by foreign material and may create a fire hazard.
Foreign materials of a conductive nature, such as but not limited to, steel wool, alu-
minum foil, or any build up of metallic particles should be kept away from the charging
plug. Unplug charger before attempting to clean.

Trigger Switch & Reversing Button

The drill is turned ON and OFF by pulling and releasing the trigger switch shown in Figure 1.
The reversing button, also shown in Figure 1, switches the drill’s direction from forward to
reverse.

Two Speed Operation

Your drill is equipped for two speed drilling. To operate at low speed, squeeze the trigger
switch halfway. This will produce a low speed to be used for driving screws and starting holes
without a centerpunch. Squeezing the trigger switch all the way will produce a high speed for
normal drilling operation.

NOTE:

There is a slight pause between speeds. Keep squeezing the trigger, and the drill will

start again.

Screw Driving

For driving fasteners, the reversing button should be pushed to the left as shown in Figure 1.
Use reverse (button pushed to the right) for removing fasteners. When moving from forward to
reverse, or vice versa, always release the trigger switch first.

Keyless Chuck (9089KB, 9099KC, 9099KB)

To insert a drill bit or other accessory: 

1. Grasp the rear half of the chuck with one hand and use your other hand to rotate the
front half in the counterclockwise direction, (Fig. 2).
2. Insert the bit or other accessory fully into the chuck, and tighten securely by holding
the rear half of the chuck and rotating the front portion in the clockwise direction as
viewed from the chuck end. 

WARNING:

Do not attempt to tighten drill bits (or any other accessory) by gripping the front

part of the chuck and turning the tool on. Damage to the chuck and personal injury may occur
when changing accessories.

Chuck & Key (9089, 9099)

Turn chuck key counterclockwise to open chuck jaws, place bit in chuck as far as it will go and
then pull it out far enough so that the chuck jaws do not touch the flutes of the bit. Tighten
chuck collar by hand. Place chuck key in each of the three holes, and tighten in clockwise
direction (Figure 3). It’s important to tighten the chuck with all three holes to prevent bit
slippage. To release bit, turn chuck key counterclockwise in just one hole, then continue to
loosen chuck by hand.

Drilling

•  When attaching accessories in the drill chuck, it is important to securely tighten the chuck

using all three holes to prevent slippage. When using a keyless chuck, hand tighten firmly. 

• Use sharp drill bits only.
• Support and secure work properly, as instructed in the Safety Instructions. 
• Use appropriate and required safety equipment, as instructed in the Safety Instructions. 
• Secure and maintain work area, as instructed in the Safety Instructions. 
• Run the drill very slowly, using light pressure, until the hole is started enough to keep the drill

bit from slipping out of it.

• Apply pressure in a straight line with the bit. Use enough pressure to keep the bit biting but

not so much as to stall the motor or deflect the bit.

Hold the drill firmly with two hands to control its twisting action.

• DO NOT CLICK THE TRIGGER OF A STALLED DRILL OFF AND ON IN AN ATTEMPT TO

START IT. DAMAGE TO THE DRILL CAN RESULT.

• Minimize stalling on breakthrough by reducing pressure and slowly drilling through the last

part of the hole.

• Keep the motor running while pulling the bit out of a drilled hole. This will help reduce jamming.
• When using twist drill bits to drill holes in wood, it will be necessary to pull the bits out

frequently to clear chips from the flutes.

• Make sure switch turns drill on and off.

Operation

DRILLING IN WOOD

Holes in wood can be made with the same twist drill bits used for metal or with spade bits.
These bits should be sharp and should be pulled out frequently when drilling to clear chips
from the flutes.

DRILLING IN METAL

Use a cutting lubricant when drilling metals. The exceptions are cast iron and brass which
should be drilled dry. The cutting lubricants that work best are sulfurized cutting oil or lard oil;
bacon grease will also serve the purpose.

DRILLING IN MASONRY

Use carbide tipped masonry bits. Refer to Drilling section. Keep even force on the drill but not
so much that you crack the brittle material. A smooth, even flow of dust indicates the proper
drilling rate.

Maintenance

Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool;
never immerse any part of the tool into a liquid.

IMPORTANT:

To assure product SAFETY and RELIABILITY, repairs, maintenance and

adjustment (other than those listed in this manual) should be performed by authorized service
centers or other qualified service organizations, always using identical replacement parts.

Battery Pack Removal

IMPORTANT:

This tool is designed for easy disassembly for the purpose of battery pack 

removal. It is not designed to be re-assembled by the consumer. Before attempting to
disassemble this tool, turn it on and run it in either direction until it stops to ensure a
complete discharge of the battery pack. To disassemble the tool, remove the screws in the
side of the tool body. Take the two body halves apart and you will find the battery pack. Lift
the battery pack out and pull off the terminal clips.

Troubleshooting

Problem

Possible Cause

Possible Solution

• Unit will not start.

• Battery not charged.

• Check battery  charging 
requirements.

• Battery will not charge.

• Charger not plugged in.

• Plug charger into a 

Refer to “Important Charging 

working outlet.

Notes” for more details.
• Check current at receptacle
by plugging in a lamp or other 
appliance.
• Check to see if receptacle 
is connected to a light switch 
which turns power off when

you turn out the lights. 

• Surrounding air 

• Move charger and tool to a 

temperature too hot or

surrounding air temperature

too cold.

of above 40 degree F(4,5°C) 
or below 105 degree F 
(+40,5°C).

For assistance with your product, visit our website 

www.blackanddecker.com

for the 

location of the service center nearest you or call the BLACK & DECKER help line at 

1-800-544-6986.

Avertissements de sécurité généraux pour les outils
électriques

AVERTISSEMENT! Lire tous les avertissements de sécurité et toutes les

directives. 

Le non-respect des avertissements et des directives pourrait se solder

par un choc électrique, un incendie et/ou une blessure grave.

Conserver tous les avertissements et toutes les directives pour un usage 
ultérieur.

Le terme «outil électrique» cité dans les avertissements se rapporte à votre outil
électrique à alimentation sur secteur (avec fil) ou par piles (sans fil).

1) Sécurité du lieu de travail

a) Tenir la zone de travail propre et bien éclairée. 

Les endroits sombres sont souvent

des causes d'accidents.

b) Ne pas faire fonctionner d’outils électriques dans un milieu déflagrant, soit en

présence de liquides inflammables, de gaz ou de poussière.

Les outils électriques

produisent des étincelles qui peuvent enflammer la poussière ou les vapeurs.

c) Éloigner les enfants et les curieux au moment d’utiliser un outil électrique.

Une 

distraction pourrait vous en faire perdre la maîtrise.

2) Sécurité en matière d’électricité

a) Les fiches des outils électriques doivent correspondre à la prise. Ne jamais 

modifier la fiche en aucune façon.

Ne jamais utiliser de fiche d’adaptation avec un

outil électrique mis à la terre. Le risque de choc électrique sera réduit par l’utilisation de
fiches non modifiées correspondant à la prise.

b) Éviter tout contact physique avec des surfaces mises à la terre comme des

tuyaux, des radiateurs, des cuisinières et des réfrigérateurs.

Le risque de choc 

électrique est plus élevé si votre corps est mis à la terre.

P

P

P

P

e

e

e

e

rr

rr

cc

cc

e

e

e

e

u

u

u

u

ss

ss

e

e

e

e

ss

ss

  

  

ss

ss

a

a

a

a

n

n

n

n

ss

ss

  

  

ff

ff

ii

ii

ll

ll

  

  

d

d

d

d

e

e

e

e

  

  

6

6

6

6

,,

,,

0

0

0

0

  

  

e

e

e

e

tt

tt

  

  

7

7

7

7

,,

,,

2

2

2

2

  

  

vv

vv

o

o

o

o

ll

ll

tt

tt

ss

ss

CONSERVER LE PRÉSENT GUIDE À TITRE DE RÉFÉRENCE.

RENSEIGNEMENTS IMPORTANTS 

• Il faut charger la perceuse pendant 16 heures avant de s'en servir.

• Le chargeur peut émettre un bourdonnement; les piles ou le chargeur peuvent

devenir chauds au toucher pendant le chargement.

The RBRC™ Seal

The RBRC™ (Rechargeable Battery Recycling Corporation) Seal on the nickel-
cadmium battery (or battery pack) indicates that the costs to recycle the battery
(or battery pack) at the end of its useful life have already been paid by Black &
Decker. In some areas, it is illegal to place spent nickel-cadmium batteries in the
trash or municipal solid waste stream and the RBRC program provides an environmentally
conscious alternative.
RBRC in cooperation with Black & Decker and other battery users, has established
programs in the United States and Canada to facilitate the collection of spent nickel-
cadmium batteries. Help protect our environment and conserve natural resources by
returning the spent nickel-cadmium battery to an authorized Black & Decker service center
or to your local retailer for recycling. You may also contact your local recycling center for
information on where to drop off the spent battery, or call 1-800-8-BATTERY.

Accessories

Recommended accessories for use with your tool are available from your local dealer or
authorized service center. If you need assistance regarding accessories, please call:

1-800-544-6986.

WARNING:

The use of any accessory not recommended for use with this tool could be

hazardous. For safety in use, the following accessories should be used only in the sizes
specified:
BITS, METAL DRILLING–Up to 1/4 inch (6mm). BITS, MASONRY DRILLING–Up to 1/4 inch
(6mm).
BITS, WOOD DRILLING–Up to 3/8 inch (10mm).

Service Information

All Black & Decker Service Centers are staffed with trained personnel to provide customers
with efficient and reliable power tool service. Whether you need technical advice, repair, or
genuine factory replacement parts, contact the Black & Decker location nearest you. To find
your local service location, refer to the yellow page directory under "Tools—Electric" or call:

1-800-544-6986 or visit www.blackanddecker.com

Full Two-Year Home Use Warranty 

Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material
or workmanship. The defective product will be replaced or repaired at no charge in either of
two ways.
The first, which will result in exchanges only, is to return the product to the retailer from whom
it was purchased (provided that the store is a participating retailer). Returns should be made
within the time period of the retailer’s policy for exchanges (usually 30 to 90 days after the
sale). Proof of purchase may be required. Please check with the retailer for their specific
return policy regarding returns that are beyond the time set for exchanges.
The second option is to take or send the product (prepaid) to a Black & Decker owned or
authorized Service Center for repair or replacement at our option. Proof of purchase may be
required.Black & Decker owned and authorized Service Centers are listed under
"Tools-Electric" in the yellow pages of the phone directory.
This warranty does not apply to accessories. This warranty gives you specific legal rights
and you may have other rights which vary from state to state or province to province. Should
you have any questions, contact the manager of your nearest Black & Decker Service
Center. This product is not intended for commercial use.

FREE WARNING LABEL REPLACEMENT

: If your warning labels become illegible or are

missing, call 

1-800-544-6986 

for a free replacement.

See ‘Tools-

Electric’

– Yellow Pages –

for Service &

Sales

Black & Decker (U.S.)

Inc., 

701 E. Joppa Rd.

Towson, MD 21286

U.S.A.

AVANT DE RETOURNER CE PRODUIT POUR QUELQUE

RAISON QUE CE SOIT, COMPOSER LE 

1-800-544-6986 

AVANT D’APPELER, AYEZ EN MAIN LE N° DE CATALOGUE ET LE CODE DE DATE. DANS LA PLUPART DES

CAS, UN REPRÉSENTANT DE BLACK & DECKER PEUT RÉSOUDRE LE PROBLÈME PAR 

TÉLÉPHONE. SI VOUS AVEZ UNE SUGGESTION OU UN COMMENTAIRE, APPELEZ-NOUS. VOS 

IMPRESSIONS SONT CRUCIALES POUR BLACK & DECKER.

M

M

ERCI

ERCI

D

D

A

A

VOIR

VOIR

CHOISI

CHOISI

B

B

LACK

LACK

& D

& D

ECKER

ECKER

!

!

V

V

ISITEZ

ISITEZ

WWW

WWW

.B

.B

LACKAND

LACKAND

D

D

ECKER

ECKER

.

.

COM

COM

/N

/N

EW

EW

O

O

WNER

WNER

POUR

POUR

ENREGISTRER

ENREGISTRER

VOTRE

VOTRE

NOUVEAU

NOUVEAU

PRODUIT

PRODUIT

.

.

MODE D’EMPLOI

Summary of Contents for 9089







Reviews: