BIXOLON SRP-330III Page 57 Command Manual Download

Page: 57 / 116

SRP-330/332III

Rev. 1.00

BIXOLON

- 57 -

GS $

Function:

Set absolute vertical print position in page mode

Code:

ASCII

Hex

Decimal

Range:

0 ≤ (nL + nH x 256) ≤ 65535 (0 ≤ nL ≤ 255, 0 ≤ nH ≤ 255)

Default:

None

Description:

This command sets the absolute vertical print starting position to [(nL + nH × 256) × (vertical or horizontal motion unit)].

Remarks:

■

This command is activated only in page mode and ignored in standard mode.

■

Either vertical or horizontal motion unit is used according to the print direction set by ESC T as follows:

•

With the starting position of the upper left or lower right on the print area, the vertical motion unit is used.

•

In other cases, the horizontal motion unit is used.

■

The configuration beyond the print area set by ESC W is ignored.

Differences:

None

Summary of Contents for SRP-330III





















































































































Search results

Summary of Contents for SRP-330III

Reviews:

Related manuals for SRP-330III

Brands by name

Popular brands

BIXOLON SRP-330III, Command Manual

Search results

Summary of Contents for SRP-330III

Reviews:

Related manuals for SRP-330III

Brands by name

Popular brands