BIXOLON SRP-330III Page 49 Command Manual Download

Page: 49 / 116

SRP-330/332III

Rev. 1.00

BIXOLON

- 49 -

ESC v

Function

Transmit paper sensor status

Code

ASCII

ESC

Hex

Decimal

118

Range:

None

Default:

None

Description

■

This command transmits a byte of data specifying the paper sensor status.

■

The status of paper near end and paper end sensors is sent to the host as follows:

•

When paper near end is detected, 0x03 is transmitted.

•

When paper end is detected, 0xC is transmitted.

Remarks

■

The paper sensor status can be transmitted using GS r.

■

The near end senor is optional while paper end sensor required.

■

If the printer is not equipped with a near end sensor, the paper near end sensor is considered as normal condition.

Differences:

None

Summary of Contents for SRP-330III





















































































































Search results

Summary of Contents for SRP-330III

Reviews:

Related manuals for SRP-330III

Brands by name

Popular brands

BIXOLON SRP-330III, Command Manual

Search results

Summary of Contents for SRP-330III

Reviews:

Related manuals for SRP-330III

Brands by name

Popular brands