BIXOLON SRP-330III Command Manual Download Page 50

Page: 50 / 116

SRP-330/332III

Rev. 1.00

BIXOLON

- 50 -

ESC {

Function

Turns upside-down printing mode on/off

Code

ASCII

ESC

{

Hex

Decimal

123

Range:

0 ≤ n ≤ 255

Default:

n = 0

Description

This command selects/deselects upside-down printing mode according to the least significant bit as follows.

LSB

Upside-down mode

Turned off

Turned on

Remarks

■

This command is valid only when entered at the beginning of the line.

■

The upside-down print mode has no effect in page mode. If this command is processed in page mode,

upside-down

printing mode

is enabled when the printer returns to standard mode.

■

180 rotated characters are printed from right to left in upside-down print mode.

■

The setting of this command remains effective until ESC !, ESC @, printer reset or power cycling is executed.

Example

Normal Upside- down Mode

Differences:

None

Summary of Contents for SRP-330III





















































































































Search results

Summary of Contents for SRP-330III

Reviews:

Brands by name

Popular brands

BIXOLON SRP-330III, Command Manual

Search results

Summary of Contents for SRP-330III

Reviews:

Brands by name

Popular brands