BIXOLON SRP-330III Page 38 Command Manual Download

Page: 38 / 116

SRP-330/332III

Rev. 1.00

BIXOLON

- 38 -

ESC V

Function:

Turn 90°clockwise rotation mode on/off

Code:

ASCII

ESC

Hex

Decimal

Range:

0 ≤ n ≤ 2, 48 ≤ n ≤ 50

Default:

n = 0

Description:

■

This command turns 90° clockwise rotation mode on/off in standard mode according to the value of n as following

•

When the value of n is equal to 0 or 48, 90°clockwise rotation mode is turned off.

•

When the value of n is equal to 1, 2, 48, or 50, 90°clockwise rotation mode is turned on.

Remarks:

■

In underline mode, the underline printing for 90° clockwise rotated characters does not work, and the relationship

between vertical and horizontal directions is reversed.

■

The 90° clockwise rotation mode is not effective in page mode.

■

If set in page mode, the 90° clockwise rotation mode has effect after the printer returns to standard mode.

■

The setting of this command remains effective until ESC !, ESC @, printer reset or power cycling is executed.

Differences:

None

Summary of Contents for SRP-330III





















































































































Search results

Summary of Contents for SRP-330III

Reviews:

Related manuals for SRP-330III

Brands by name

Popular brands

BIXOLON SRP-330III, Command Manual

Search results

Summary of Contents for SRP-330III

Reviews:

Related manuals for SRP-330III

Brands by name

Popular brands