BIXOLON SRP-330III Page 51 Command Manual Download

Page: 51 / 116

SRP-330/332III

Rev. 1.00

BIXOLON

- 51 -

FS p

Function

Print NV bit image

Code

ASCII

Hex

Decimal

112

Range:

1 ≤ n ≤ 255

0 ≤ m ≤ 3, 48 ≤ m ≤ 51

Default:

None

Description

This command prints NV bit image n using the mode specified by m as follows:

Mode

0, 48

Normal

1, 49

Double-width

2, 50

Double-height

3, 51

Quadruple

Remarks

■

GS ( L and GS ( 8 can be used for printing NV bit image.

■

The NV bit image is defined by FS q.

■

n is assigned to each NV bit image to be stored in download order by FS q.

■

This command has no effect with NV bit image not defined in advance.

■

In page mode, the NV bit image is saved without being printed.

■

The printer does not print the NV bit image that is beyond one line of print area.

■

When using unidirectional print mode, there will be no vertical misali gnment between the top and bottom parts of the

printed pattern.

Summary of Contents for SRP-330III





















































































































Search results

Summary of Contents for SRP-330III

Reviews:

Related manuals for SRP-330III

Brands by name

Popular brands

BIXOLON SRP-330III, Command Manual

Search results

Summary of Contents for SRP-330III

Reviews:

Related manuals for SRP-330III

Brands by name

Popular brands