manualshive.com logo in svg

BITREK BI FLSensor, User Manual, Page: 14 / 22

Share
Download
BITREK BI FLSensor User Manual Download Page 14

 

 

 

 

14 

 

BI 810 TREK / BI 820 TREK 

 

 

 

 

ADDITIONAL INFORMATION 

Transportation and storage 

Climatic conditions of gauges transportation: 

 

ambient temperature -50... + 40 °C 

 

relative humidity 98% at temperature of +25 °C 

The  air  area  should  not  contain  acids,  alkali  and  other  aggressive 

impurities. 

 

 Storage 

The  gauges  shall  be  stored  in  the  manufacturer's  packaging,  in 

closed  spaces  with  natural  ventilation,  without  artificially  controlled 

climatic conditions, without heating. Storing of gauges without packaging 
is  not  allowed.  It  is  forbidden  to  store  the  gauges  in  the  same  premise 

with substances causing metal corrosion and substances with aggressive 
impurities. 

 

Operating conditions 

The  gauge  shall  be  used  for  units  with  a  successful  fuel  supply 

system. 

The marking for mounting of the gauge assembly shall conform to 

mounting holes. 

The  gauge  shall  be  protected  from  corrosive  environment, 

electromagnetic  field, as well as mechanical and environmental  stresses 
that exceed the parameters indicated in the specification to prevent from 

failure. 

Do  not  connect  the  gauge  to  the  devices  with  interface  that  does 

not meet the characteristics specified in the passport. 

Summary of Contents for BI FLSensor























Reviews:

No comments