background image

Place the TurboBrush in the Bracket by aligning the 
bottom of bracket with the opening of the brush roll 
and snap the TurboBrush into place.

Press the Handle Release Pedal with your foot to place 
your vacuum in one of three cleaning positions.

Upright- For storage and above floor cleaning with tools.

Normal Cleaning- Press Handle Release Pedal once. 
Use for most household floor cleaning tasks.

Low Cleaning- With the vacuum in normal cleaning position, 
press Handle Release Pedal again. Use for reaching under 
low furniture such as tables, chairs or beds.

 The Powerfoot/Rotating Floor Brush can be 
adjusted to clean several floor surfaces. 

NOTE: For optimal cleaning performance, 
adjust to the lowest practical setting. If 
your cleaner is difficult to push, adjust to 
the next higher setting. 

Place Handle in Upright Position. 

Turn Height Adjustment Knob to desired setting.

Lowest Setting 

For bare floors.

Medium Settings

  For short and medium 

 pile 

carpets.

Highest Setting

 

For plush pile carpet.

Place the Handle in the normal cleaning position and 
the Powerfoot will adjust to the setting chosen. 

NOTE: You may also adjust the setting 
while in the normal cleaning position.

To move your cleaner from room to room, put the 
Handle in the upright position, tilt the cleaner back on 
its rear wheels and push forward. 

 The cleaner can also be moved by using the Carrying 
Handle on the back.

Attach Vacuum Hose and Tools Continued

6

1.

2.

3.

Height Adjustment

How To Use Your Vacuum

Handle Positions

1.

2.

3.

 

CAUTION:

 

Before using your vacuum, 
make sure that the Dirt 
Container is in locked 
position and that all filters 
(Inner Circular, Outer Circular, 
Pre-Motor and Post-Motor) are 
in place. Do not operate your 
vacuum without these filters.

Tip:

Your vacuum features 
a Quick Release Cord 
Wrap. To remove the 
Power Cord quickly 
and easily, rotate the 
Upper Cord Wrap 
towards floor, and 
slip Power Cord from 
Upper and Lower 
Cord Wraps.

Tip:

Before cleaning under 
low furniture, check 
area first for objects 
that might harm the 
unit or block the 
Vacuum Hose.

5

Carrying Handle

7.

Transporting Cleaner

1.

2.

ug203-2829_6596_1105.indd   6

ug203-2829_6596_1105.indd   6

1/11/06   4:03:36 PM

1/11/06   4:03:36 PM

Summary of Contents for 6596

















Reviews: