background image

To maintain maximum cleaning performance, the 
following maintenance steps must be performed:

Empty the Dirt Container when the dirt reaches the 
“Full” line on the side. 

Check the Inner and Outer Circular Filters and the 
Pre-Motor Filter at least once a month and clean or 
replace as needed.

Replace the Post-Motor Filter every three to six months.

Note: More frequent filter cleaning or 
replacing may be necessary if you are 
vacuuming new carpet, fine dust, or have 
allergy concerns. Follow the instructions on 
the following pages to perform these simple 
maintenance steps.

The Dirt Container needs to be emptied when the dirt 
reaches the “Full” line on the side of the Container.

Unplug cleaner from electrical outlet.

Slide the Lock ‘n Seal Lever to the "Unlock" position.

Grasp handle and pull the Dirt Container straight out to 
remove from vacuum.

Empty dirt into garbage container.

Put the Dirt Container back in the vacuum and slide the 
lever to the "Lock" position.

Note: The Dirt Container may be washed in 
warm water with a mild detergent. Remove 
the Filter Cup from the bottom before 
washing. Reassemble and make sure it is 
completely dry before using again.

Use only BISSELL Style 9 Replacement Filters in 
your BISSELL CleanView II.

Unplug the cleaner from electrical outlet.

Remove the Dirt Container as described in the previous 
section. Grasp the Filter Cup located at the bottom of 
the Dirt Container and twist counterclockwise to unlock 
and remove.

Grasp the Circular Filters and twist to unlock. Pull 
straight up to remove.

8

How To Maintain Your Vacuum

1.

2.

3.

Empty Dirt Container

1.

2.

3.

4.

5.

Tip:

For maximum cleaning 
performance, check 
and clean or replace all 
filters as suggested.

 WARNING:

 

To reduce the risk of 
electric shock, turn Power 
Switch OFF and discon-
nect polarized 
plug from electrical outlet 
before performing 
maintenance or 
troubleshooting checks.

Full Line

Lock Position

Unlock 

Position

Cleaning The Inner & Outer Circular Filters

1.

2.

3.

ug603-2559_3574-3576_1005.indd   8

ug603-2559_3574-3576_1005.indd   8

1/4/06   9:45:56 AM

1/4/06   9:45:56 AM

Summary of Contents for 20Q9

















Reviews: