background image

1

NOTICE TO OWNERS AND OPERATORS

 

BIRO’s products are designed to process food products safely and efficiently. Unless the operator is 

properly trained and supervised, however, there is the possibility of a serious injury. It is the responsibility of 

the owner to assure that this machine is used properly and safely, strictly following the instructions contained in 

this Manual and any requirements of local law. 
 

No one should use or service this machine without proper training and supervision. All operators should 

be thoroughly familiar with the procedures contained in this Manual. Even so BIRO cannot anticipate every cir-

cumstance or environment in which its products will be used. You, the owner and operator, must remain alert to 

the hazards posed by the function of this equipment - particularly the ROTATING GRINDING WORM, which 

can severely injure an inattentive operator amputating fingers and limbs. No one under eighteen (18) years of 

age should operate this equipment. If you are uncertain about a particular task, ask your supervisor. 
 

This Manual contains a number of safe practices in the SAFETY TIP section. Additional warnings are 

placed throughout the Manual. Warnings related to your personal safety are indicated by:

OR

 

Warnings related to possible damage to the equipment are indicated by:

 

BIRO also has provided warning labels on the equipment. If any warning label or Manual becomes 

misplaced, damaged, or illegible, please contact your nearest Distributor or BIRO directly for a replacement.

 

 

Remember, however, this Manual or the warning labels do not replace the need to be alert and to use

your common sense when using this equipment. 

“A copy of this manual is included with each Model 722 Grinder.”

- NOTE -

“The descriptions and illustrations contained in this manual 

are not binding. The manufacturer reserves the right to 

introduce any modification without updating the manual .”

Summary of Contents for 722

















Reviews: