Biolase Waterlase iPlus User Manual Download Page 58

Page: 58 / 82

Appendix A

Labels

5200193

REV. C

ELECTRICAL RATINGS

100 - 230 V

50/60 HZ

15 A / 8 A

Waterlase iPlus User Manual

LASER EXPLANATORY LABEL

Provides laser speci�cations
Location: On top cover, adjacent to Fiber Cable connector

SYSTEM GROUND CONNECTION

Location: Inside Laser Console, left.

ELECTRICAL SHOCK RATINGS

Type BF Applied Part
Location: Next to E1 ground terminal, inside Laser

Console.

REMOTE INTERLOCK LABEL

Input for Remote Interlock Connector which, when applied

to the access door of the operatory and activated, will

shut off the laser.
Location: Back panel

ETL LISTED: UL/CSA CONFORMANCE LABEL

Location: Back panel

FOOTSWITCH LABEL

Connection to Footswitch
Location: Back panel

WEIGHT

LABEL

Location: Back panel

Summary of Contents for Waterlase iPlus



















































































Search results

Summary of Contents for Waterlase iPlus

Reviews:

Related manuals for Waterlase iPlus

Brands by name

Popular brands

Biolase Waterlase iPlus, User Manual

Search results

Summary of Contents for Waterlase iPlus

Reviews:

Related manuals for Waterlase iPlus

Brands by name

Popular brands