Bioer ThermoShaker MB-202 Operation Manual Download Page 3

Operation Manual for Oscillating Dry Bath                                                                      Important Notes 

 

II

 — 

 

Important Notes 

1. General Practice   

 

Caution

 

Important information is contained in any item and should be carefully read. Failure 
to  observe  the  instructions  would  result  in  damage  to  or  malfunction  of  the 
equipment. 

 

Warning! 

The warning message requires extremely careful operation of a certain step. Failure 
to observe the instructions may result in serious personal injuries. 

 

2. Safety 

During operation, maintenance and repair of this instrument, the following basic safety measures 

shall be observed. In case of failure to follow these measures or the warnings or notes indicated herein, 

the basic protection provided by the instrument, its safety criteria of design and manufacture, and its 

predicted use range would be impaired. 

Hangzhou Bioer Technology Co., Ltd. would be irresponsible for any consequence resulted from 

the user’s failure to observe the following requirements. 

 

Caution:   

This instrument is for indoor use.   

 
a) The ground connection   

To  avoid  the  electric  shock,  the  input  power  line  must  be  reliably  grounded.  The  instrument  is 

equipped with the three-pin plug that has the third pin (the pin connects the ground), therefore, the plug 

shall be used with the grounded power socket only. This is a kind of safety device. If the plug cannot 

be plugged into the power socket, please ask the electrician to install a correct power socket, so as to 

make the grounded plug to work for safety. 

 

b) Keeping apart from the live circuit 

The  operator  shall  not  disassemble  the  instrument  without  permission.  Only  qualified 

professionals are  allowed to  replace  elements  or adjust  the  machine inside.  Replacement  of elements 

under energizing state is prohibited. 

 

c) Be careful of the power supply 

 

Before  the  instrument  is  connected  with  the  AC  power  source,  the  voltage  of  the  power  source 

shall  be  the  same  with  the  required  voltage  of  the  instrument  (a  deviation  of 

10%  is  allowed).  The 

rated load of the power socket shall not be lower than the requirements of the instrument. 

 

d) Be careful of the power line 

Usually,  the  instrument  shall  use  the  power  line  attached  to  it.  If  the  power line  is  destroyed,  it 

Summary of Contents for ThermoShaker MB-202






















Reviews: