background image

 

 

 

 

 

 

C 150 (E2) 06/2011 

page 69/78 

 

CAUTION 

 

Violation against existing law. 

  Do NOT dispose of BINDER devices at public collecting points.  

¾

  Have the device disposed of professionally at a recycling company that is certified ac-

cording to conversion of the directive 2002/96/EC into national law. 

 

or

 

¾

  Instruct the distributor who sold you the device to dispose of it. The agreements apply 

that were agreed with the distributor when purchasing the unit (e.g. his general terms of 
payment and delivery). 

¾

  If your distributor is not able to take back and dispose of the unit, please contact 

BINDER Service. 

Certified companies disassemble waste (used) BINDER equipment in primary substances for recycling 
according to directive 2002/96/EC. The devices must be free from toxic, infectious or radioactive sub-
stances in order to eliminate any health hazards to the employees of the recycling companies.  

 

Prior to handing the unit over to a recycling company, it is the user’s responsibility that it is 
free from toxic, infectious or radioactive substances. 

  Prior to disposal, clean all introduced or residual toxic substances from the unit. 

  Prior to disposal, disinfect the unit from all sources of infection. Be aware that sources of 

infection may also be located outside the inner chamber. 

  If you cannot safely remove all sources of infection and toxic substances from the unit, 

dispose of it as “special” waste according to national law. 

  Fill out the contamination clearance certificate (chap. 19) and enclose it with the unit. 

 

WARNING 

 

 

Contamination of the device with toxic, infectious or radioactive substances. 

Danger of intoxication. 

Danger of infection. 

  NEVER take a unit contaminated with toxic substances or sources of infection for recy-

cling according to directive 2002/96/EC. 

¾

  Prior to disposal, remove all toxic substances and sources of infection from the unit. 

¾

  A unit from which all toxic substances or sources of infection cannot be safely removed 

must be considered as “special” waste according to national law. Dispose of it accord-
ingly. 

 

17.5  Disposal of the unit in non-member states of the EC 

CAUTION 

 

 

Alteration of the environment. 

¾

  For final decommissioning and disposal of the CO

2

 incubator, please contact BINDER 

Service. 

¾

  Follow the statutory regulations for appropriate, environmentally friendly disposal. 

The main board of the CO

2

 incubator includes a lithium cell. Please dispose of it according to national 

regulations. 

Summary of Contents for APT.line C 150
















































































Reviews: