Billion BiPAC 8900X R3 User Manual Download Page 10

Page: 10 / 261

ATM, PTM and PPP Protocols

• ATM Adaptation Layer Type 5 (AAL5)

• Multiple Protocol over ALL5 (RFC 268, formerly RFC 1483)

• Bridged or routed Ethernet encapsulation

• VC and LLC based multiplexing

• PPP over Ethernet (PPPoE)

• PPP over ATM (RFC 2364)

• Classical IP over ATM (RFC 1577)

• MAC Encapsulated Routing (RFC 1483 MER)

• OAM F4 / F5

IPTV Applications

• IGMP Snooping and IGMP Proxy

• MLD Snooping and MLD Proxy

• Interface Grouping (VLAN)

• Quality of Service (QoS)

USB Application Server

• 3G/4G LTE dongle support

• Storage: FTP server, Samba server

，

DLNA

• Printer Server

Virtual Private Network (VPN)

• 16 IPSec VPN tunnels

• IKE key management

• DES, 3DES and AES encryption for IPSec

• L2TP over IPSec

• Pap/ Chap/ MS-CHAPv2 authentication for PPTP

• IPSec pass-through

• GRE tunnel

Management

• Easy Sign-on (EZSO)

• Web-based GUI for remote and local management (IPv4/IPv6)

• Firmware upgrades and configuration data upload and download via web-based GUI

• Embedded Telnet server for remote and local management

• Supports DHCP server / client / relay

• Supports SNMP v1,v2, MIB-I and MIB-II

Summary of Contents for BiPAC 8900X R3






































































































































































































































































Search results

Summary of Contents for BiPAC 8900X R3

Reviews:

Billion BiPAC 8900X R3, User Manual, Page: 10 / 261

Search results

Summary of Contents for BiPAC 8900X R3

Reviews: