manualshive.com logo in svg

Billion BiPAC 8900X R3, User Manual

The Billion BiPAC 8900X R3 is a cutting-edge networking device that will revolutionize your internet experience. Unlock its full potential by accessing the detailed User Manual, available for free download from our website. Explore the versatility and power of this device through our comprehensive manual, only a click away.

Share
Download
background image

207 

 

 

GRE 

Generic Routing Encapsulation (GRE) is a tunneling protocol that can encapsulate a wide variety 
of  network  layer  protocol  packets  inside  virtual  point-to-point  links  over  an  Internet  Protocol  (IP) 
network.  
 

Note:

 up to 8 tunnels can be added, but only 4 can be activated. 

 

 

 

Name: User-defined identification. 

WAN  Interface: Select the exact WAN interface configured for the tunnel as the source tunnel IP. 
Select Default to use the now-working WAN interface for the tunnel. 

Local Tunnel Virtual IP: Please input the virtual IP for the local tunnel. 

Local Netmask: Input the netmask for the local tunnel. 

Remote Tunnel Virtual IP: Please input the virtual destination IP for tunnel. 

Remote Gateway IP: Set the destination IP for the tunnel. 

Remote Network: Select the peer topology, Single address (client) or Subnet. 

IP Address: Set the IP address if the peer is a client. If the peer is a subnet, please enter the IP and 
netmask. 

Enable Keepalive: Normally, the tunnel interface is always up. Enable keepalive to determine when 
the  tunnel  interface  is to be  closed. The  local  router  sends  keepalive  packets  to  the peer  router,  if 
keepalive  response  is  not  received  from  peer  router  within  the  allowed  time  (‘retry  time’  multiply 
‘interval’, based on default settings, the time interval can be 30 seconds), the local router will shut up 
its tunnel interface. 

Keepalive Retry Times: Set the keepalive retry times, default is 10. 

Keepalive Interval: Set the keepalive Interval, unit in seconds. Default is 3 seconds. 

 

 

 

 

 
 
 

 
 
 

Summary of Contents for BiPAC 8900X R3






































































































































































































































































Reviews:

No comments

Related manuals for BiPAC 8900X R3

D-Link DIR-862L Manual preview
DIR-862L
Brand: D-Link Pages: 4
D-Link DIR-860L Quick Install Manual preview
DIR-860L
Brand: D-Link Pages: 2
D-Link DIR-850L Resetting Manual preview
DIR-850L
Brand: D-Link Pages: 9
D-Link DIR-850L Setup And Installation Manual preview
DIR-850L
Brand: D-Link Pages: 8
D-Link DIR-865L Specifications preview
DIR-865L
Brand: D-Link Pages: 3
D-Link DIR-867 Quick Install Manual preview
DIR-867
Brand: D-Link Pages: 28
D-Link DIR-X1530 Quick Start Manual preview
DIR-X1530
Brand: D-Link Pages: 2
D-Link DSL-2540B - ADSL2/2+ Modem With EN Router Quick Install Manual preview
DSL-2540B - ADSL2/2+ Modem With EN Router
Brand: D-Link Pages: 12
D-Link DIR-882 Quick Installation Manual preview
DIR-882
Brand: D-Link Pages: 62
REXROTH efc series Instruction Manual preview
efc series
Brand: REXROTH Pages: 68
LaCie 5BIG NAS PRO Quick Install Manual preview
5BIG NAS PRO
Brand: LaCie Pages: 22
Caimore CM520-86EG User Manual preview
CM520-86EG
Brand: Caimore Pages: 79
IBM BladeCenter Management Module Installation And User Manual preview
BladeCenter Management Module
Brand: IBM Pages: 184
EVOC 6336-STG-YX Manual preview
6336-STG-YX
Brand: EVOC Pages: 57
IMC Networks iMcV-FiberLinX Operation Manual preview
iMcV-FiberLinX
Brand: IMC Networks Pages: 36
TP-Link Archer C7 How To Set Up preview
Archer C7
Brand: TP-Link Pages: 4
2N Telekomunikace ATEUS STARGATE User Manual preview
ATEUS STARGATE
Brand: 2N Telekomunikace Pages: 67
ADTRAN 1700601G2 Quick Start Manual preview
1700601G2
Brand: ADTRAN Pages: 4

Brands by name

Popular brands

Load more brands