manualshive.com logo in svg

Billion BiPAC 8800AXL, User Manual

Share
Download
Billion BiPAC 8800AXL User Manual Download Page 170

166

 

 

QoS - Quality of Service 

 

Quality of Service 

QoS helps you to control the data upload traffic of each application from LAN (Ethernet) to WAN 
(Internet). This feature allows you to control the quality and speed of throughput for each application 
when the system is running with full upstream load. 
 

Note:

 

ADSL line speed is based on the ADSL sync rate. But there is no QoS on 3G/LTE as the 

3G/LTE line speed is various and can not be known exactly.

 

 

 

 

EWAN Line Speed 

 

Upstream / Downstream: 

Specify the upstream and downstream rate of the EWAN interface. 

Click 

Apply

 to save the EWAN rate settings. 

 
Click 

Add

 to enter QoS rules. 

 

 

IP Version: 

Select either IPv4 or IPv6 base on need. 

Application: 

Assign a name that identifies the new QoS application rule. Select from the list box for 

quick setup.

 

Direction: 

Shows the direction mode of the QoS application.

 

 

LAN to WAN: 

You want to control the traffic from local network to the outside (Upstream). 

You can assign the priority for the application or you can limit the rate of the application.  

Eg:

 you have a FTP server inside the local network, and you want to have a limited control by 

the QoS policy and so you need to add a policy with LAN to WAN direction setting.

 

 

WAN to LAN: 

Control traffic from WAN to LAN (Downstream). 

 

Summary of Contents for BiPAC 8800AXL







































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands