Billion BiPAC 6404VGP R3 User Manual Download Page 20

Page: 20 / 119

Factory Default Settings

Before configuring your router, you need to know the following default settings.

Web Interface (Username and Password)

Username: admin

Password: admin

The default username and password are “

admin

” and “

admin

” respectively.

Device LAN IP settings

IP Address: 192.168.1.254

Subnet Mask: 255.255.255.0

ISP setting in WAN site

PPPoE

DHCP server

DHCP server is enabled.

Start IP Address: 192.168.1.100

IP pool counts: 100

LAN and WAN Port Addresses

The parameters of LAN and WAN ports are pre-set in the factory. The default values are shown in
the table.

LAN Port

WAN Port

IP address

192.168.1.254

Subnet Mask

255.255.255.0

DHCP server function

Enabled in ports 1, 2, 3 and
4

IP addresses for distribution
to PCs

100 IP addresses continuing
from 192.168.1.100 through
192.168.1.199

The PPPoE function is

enabled

to automatically get

the WAN port configuration
from the ISP.

Summary of Contents for BiPAC 6404VGP R3
























































































































Search results

Summary of Contents for BiPAC 6404VGP R3

Reviews:

Related manuals for BiPAC 6404VGP R3

Brands by name

Popular brands

Billion BiPAC 6404VGP R3, User Manual

Search results

Summary of Contents for BiPAC 6404VGP R3

Reviews:

Related manuals for BiPAC 6404VGP R3

Brands by name

Popular brands