Billion BiPAC 6404VGP R3 User Manual Download Page 108

Page: 108 / 119

106

Configuration of Time Schedule

Edit a Time Slot

1. Choose any Time Slot (ID 1 to ID 16) to edit, click Edit radio button.

Note: Watch it carefully, the days you have selected will present in capital letter. Lower case

letter shows the day(s) is not selected, and no rule will apply on this day(s).

A detailed setting of this Time Slot will be shown.

ID:

This is the index of the time slot.

Name:

A user defined description to identify this time portfolio.

Day in a week:

The default is set from Monday through Friday. You may also specify the days for

schedule to be applied to.

Start Time:

The default is set at 8:00 AM. You may specify the start time of the schedule.

End Time:

The default is set at 18:00 (6:00PM). You may specify the end time of the schedule.

Choose Edit radio button and click Edit/Delete button to apply your changes.

Summary of Contents for BiPAC 6404VGP R3
























































































































Search results

Summary of Contents for BiPAC 6404VGP R3

Reviews:

Related manuals for BiPAC 6404VGP R3

Brands by name

Popular brands

Billion BiPAC 6404VGP R3, User Manual

Search results

Summary of Contents for BiPAC 6404VGP R3

Reviews:

Related manuals for BiPAC 6404VGP R3

Brands by name

Popular brands