background image

Wood Parts

Front Top 1 x 6 x 83"

Hardware

Lower Front Post 2 x 4 x 57¾"

B24

2X

x 2¾” hex bolt (with flat washer, lock washer and t-
nut) and to

1X

C14

Top Back 1 x 6 x 83"

H11

#8 x 1½” wood screws. 

E15

1X

1X

Hex Bolt 1/4 x 2¾"

E29

1X

1X

Wood Screw #8 x 1½"

 (S2)

Ground Front Back using 2

 (C8) 

Upper Front Post 2 x 4 x 48¾"

13X S2

A

:  Attach

 (E15)

 Top Back to both

 (B16)

 Roof 

Blocks and the

 (C9) 

Roof Upright using 6

 (S2)

 #8 x 

1½” wood screws.

B

:  Attach

 (E29)

 Front Top to 2 

(B16)

 Roof Blocks 

using 2 

(S2)

 #8 x 1½” wood screws per side as 

shown below.

C

:  Attach 

(B24)

 Upper Front Post to the

 (E29)

Front Top using 1 

(H2)

 1/4 x 2” (with flat washer, 

lock washer and t-nut) in the upper hole and 1 

(S2)

#8 x 1½” wood screw in the lower hole and to 

(B19)

 Front Floor using 1 

(H11)

 1/4 x 2¾” hex bolt 

(with flat washer, lock washer and t-nut).

D

:  Then attach 

(C14)

 Lower Front Post to 

(B19)

Front Floor directly under

 (B24)

 using 1 (H11) 1/4 

H2 Hex Bolt 1/4 x 2"

STEP 11 

Attach Top Front/Back and Front Posts

H2

B16

E29

E15

B16

S2

S2

S2

B16

B24

C14

B16

C9

C8

H11

B19

Note: Make sure the arches
of

(E15)

 are oriented correctly

Larger arch

Smaller arch

26

Summary of Contents for F23475





























































Reviews: