10
English
IMPORTANT SAFETY ADVICE.-
PRECAUTIONS.
This bicycle has been designed and constructed to
provide maximum safety. Nevertheless, certain
precautions should be taken when using exercise
equipment.
Read the whole manual before assembling and
using the bicycle. It provides you with important
information about assembly, safety and use of the
machine.
The following safety precautions should also be
observed:
1
Keep children away from this equipment at all
times. DO NOT leave them unsupervised in the
room where this bicycle is kept.
2
It can only be used by one person at a time.
3
If you experience dizziness, nausea, chest pains
or any other symptom while using this appliance
STOP the exercise. SEEK MEDICAL ATTENTION
IMMEDIATELY.
4
Use the appliance on a level, solid surface. DO
NOT use the bicycle outdoors or close to water.
5
Keep your hands well away from any of the
moving parts.
6
Wear clothing suitable for doing exercise. Do not
use baggy clothing that might get caught up in the
bicycle. Always wear running shoes or trainers
when using the machine. Make sure all laces/cords
are tied correctly.
7
This appliance must only be used for the
purposes described in this manual. DO NOT use
accessories that are not recommended by the
manufacturer.
8
Do not place sharp objects near the machine.
9
Disabled people should not use the machine without
the assistance of a qualified person or a doctor.
10
Do warm up stretching exercises before using
the equipment.
11
Do not use the bicycle if it is not working
correctly.
Caution: Consult your doctor before beginning
to use the bicycle. This advice is especially
important for those over 35 or suffering from
health problems.
Keep these instructions safe for future use.
GENERAL INSTRUCTIONS.-
1
This unit has been designed for professional use.
The weight of the user must not exceed 150 kg.
2
Parents and/or those responsible for children
should always take their curious nature into account
and how this can often lead to hazardous situations
and behaviour resulting in accidents.
Under no circumstances should this appliance be
used as a toy.
3
The owner is responsible for ensuring that
anyone who uses the machine is duly informed
about the necessary precautions.
ASSEMBLY INSTRUCTIONS.-
The assistance of a second person is
recommended when assembling this unit.
WARNING: The replacement of any
component with another not supplied
by BH will void the warranty.
TOOLS NEEDED.-
Hex wrench (55)
(supplied)
Loctite 242
Cod 0190248 (*)
2 No. 14 wrench for
M8 nuts (*)
BH rust inhibitor
cod 0190236 (*)
Torque wrench cod
0190245 (*)
Clean cloths. (*)
Wrench for M6 nut (*)
Multilube Wurth lubricant
spray cod 0190249 (*)
3 mm Allen key (*)
Meguiar's Nxt soap
Philips screwdriver (*)
BH indoor cycling
protector cod 0190237 (*)
(*)
Not supplied. Optional.
Take the unit out of its box and make sure that all of
the pieces are there (Fig. 1):
(A) Main body; (20) Handlebar; (21) Handlebar
stem; (39) Saddle post; (38) Horizontal saddle tube;
(1) Saddle; (63) cover for handlebar; (11) Rear
stabiliser bar with adjustable feet; (14) Front
stabiliser bar with wheels; (9L) Left pedal; (9R)
Right pedal; (8) Slot head bolt M10; (7) Flat washer
M10; (6) Cap nut M-10; (15) Bottle holder; (62)
Console; (101) Monitor plate; (M) Handlebar
support piece; Double ended spanner.
1.
Position the machine’s rear stand on the rear
stabilizer bar (11), as shown in Fig.2, insert the
bolts (8), fit the flat washers (7) and cap nuts (6)
and then tighten securely.
2.
Position the front stabiliser bar with wheels (14),
paying attention to the red dots and with the wheels
facing forwards, as shown in Fig.2, insert the bolts
(8), fit the flat washers (7) and cap nuts (6) and
tighten securely.
FITTING THE HANDLEBAR.-
Remove the plug (53) and place the handlebar (20)
in the position closest to the knob (G03) with two
screws. Insert the upper part (23) at the bottom (21)
and make sure the knob (G03) tightened properly
before replacing the cap (53). Fig. 3C.
Fit the cover for handlebar (63) in the handlebar
post. Position the handlebar (20) on the handlebar
stem (21), Fig.3B, tighten the knob (17) and then
insert the handlebar stem (21) into the hole on the
main body (A), Fig.3B.
Summary of Contents for H945ANT
