10
ASSEMBLY INSTRUCTIONS.-
1.-
Take the unit out of its box and
make sure that all of the pieces are
there, Fig.1:
(1) Main body; (6) Main post; (7)
handlebar; (8) Electronic monitor; (4)
Saddle post; (2) Front stabiliser bar
with wheels; (3) Rear stabiliser bar
with adjustable feet; (5) Saddle;
Pedals (19) Right and (18) Left; (20)
Bottle holder; Handlebar cover (14)
left, (15) right and (13) fontera; (21)
Handlebar plug; Seat cover (16) left
and right (17); (23) Saddle knob; (29)
Screws M-4x6; (32) Screws M-4x16;
(87) Screws M-4x12; (27) Spring
washer M10; (28) Flat washer M10;
(26) Screws M-10x70x20; (31) Screws
M-12x60.
2.- FITTING THE STABILISER
BARS.-
ATTENTION: The assistance of a
second person is required for this
stage of the assembly.
Take the stabilizer bar with wheels (2)
and place it on the front of the unit, as
shown in Fig.2, insert the screws (26),
place the washers (27) and (28).
Then take the rear stabiliser bar with
the adjustable blocks (3) and carry out
the same assembly operation as with
the front stabiliser bar, tighten up all
securely.
3.- ATTACHING THE SADDLE.-
Insert the Saddle post (4) through the
hole in the main body (1), Fig.4.
Attach the saddle (5) to the slide (60)
with the nuts (59). Fig 5b.
Place the saddle (5) on the Saddle post
(4), position the saddle knob (23) with
the bushing (25), secure the saddle in
its comfortable position with the knob
(23) and tighten by turning clockwise
direction. Attach the left (17) and right
(16) saddle covers with screws (29).
Fig.5.
4.- FITTING THE MAIN POST.-
Bring the main post (6) up to the boss
on the main body (1), Fig.6, and
connect terminals (9) and (10).
5.- FITTING THE HANDLEBAR.-
Position the handlebar (7) to the Main
post (6), Fig.7, install the handlebar
cover (13) with the knob (21) and
tighten them. Check the alignment of
the handlebar before tightening all
screws. Then position the bottle holder
(20) with screw (32).
6.- FITTING THE ELECTRONIC
MONITOR.-
Remove the screws (24) from the back
of the monitor, then place the monitor
on top of the main post (6) making sure
not to pinch any of the cables. Refit the
screws and tighten, connect the
handgrip terminal (11) and the
feedback terminal (9) at the back of the
monitor, as shown in Fig.8.
Then attach the left handle cover (14)
and right handle cover (15) with screws
(32). Screw the front handlebar cover
(13) with screws (87).
7.- ATTACHING THE PEDALS.-
The assembly instructions for the
pedals must be followed to the
letter, fitting these incorrectly could
damage the screw thread on the
pedal or the crank.
Right and left refer to the position that
the user adopts when sitting on the
saddle to do the exercises.
The right pedal (19) is marked with the
letter (R).
Summary of Contents for H832TFT
