background image

7

1.  Machine safety label 

 

 

 

„Before setting-up, servicing, maintaining and clea-

ning the machine, disengage power and stop the 

engine. Lock the tool and secure it against acciden-

tal start.“ 

 

 

 

 

This safety label reminds users of a pinched hands danger.

  

 

 

 

 

 

 

 

2.  Machine safety label 

 

 

 

„Read, understand, and follow all instructions in 

this manual and on the splitter before starting!“    

Keep at safe distance from machine moving parts!   

3.  Operation safety label „ADJUSTING THE SPLIT-

TING SPEED“  

 

 

 

 

This label shows how to operate the control levers

 

4.  Operation safety label „max p 240 bar“

This label shows the max admissible operating pressure. 

5.  Operation safety label “Pinched hands danger!“ 

Keep your hands off all moving machine parts! Pinched hands hazard 

in the wedge dangerous area. 

6. Maintenance label „Lubricate every 10 h“

   

  

 

 

 

 

   

  

 

 

 

 

7. Machine safety label „Direction arrow“

The motor must be turning in the same direction as shown by this ar-

row. 

 

8.  Machine safety label „Mind this direction arrow“ 

The motor must turn in the same direction as shown by this arrow.     

 

 

 

 

 

 

 

3.  WARNING LABELS AND SAFETY DECALS

p max 240 bar

Summary of Contents for USP 13-6

































Reviews: