background image

12

11.1 Scope of Warranty

BEYES Dental Canada Inc. (‘BEYES’) warrants to the original retail purchaser that it will be at BEYES 

option to repair or replace components of the dental products manufactured by BEYES (except for 

components not warranted under ‘Exclusions’) that are defective in material or workmanship under 

normal use and service. BEYES’ obligation under this limited warranty is limited to the repair or 

replacement of the applicable components. This limited warranty shall only apply to defects that are 

reported to BEYES within the applicable warranty period and which, upon examination by Beyes, 

prove to be defective. This warranty extends only to the first retail purchaser of a product and is not 

transferable or assignable. Replacement components or products may be used and/or refurbished 

components or products, provided they are of like quality and specifications as new components or 

products.

11.2 Applicable Warranty Period

The applicable warranty period, measured from the date of invoice to the original user, shall be 

warranted for a period of 25 months.

11.3 Exclusions

This limited warranty does not cover and BEYES shall not be liable for the following;

1) Defects, damage or other conditions caused, in whole or in part, by misuse, abuse, negligence, 

alteration, accident, freight damage, negligent storage, tampering or failure to seek and obtain repair 

or replacement in a timely manner; 

2) Products which are not installed, used, and properly cleaned and maintained as required or 

recommended in the BEYES ‘Installation’ and/or ‘Installation/User’s Manual’ for the applicable 

product, including the specified structural and operational environment conditions and electrical 

power requirements;

3) Products considered to be of a consumable or sterile nature;

4) Accessories or parts not manufactured by BEYES;

5) Charges by anyone for adjustments, repairs, replacement parts, installation or other work 

performed upon or in connection with such products which are not expressly authorized in writing in 

advance by BEYES;

LED does not light up

Reached the end of life expec-

tancy

Contact your dealer

Motor heats up abnormally 

during rotation

Coolant air is not coming out of 

the delivery unit

Check the air pressure of the 

delivery system

Water Leakage

Turbine, Motor cord is not 

connected correctly

Check the connection

When turned on, the setting 

values are different from what 

they were set to.

Turned off the motor while it 

was rotating

Do not turn off the unit until 

after the motor stops spinning

11. Beyes Limited Warranty Statement

Summary of Contents for Maxso E600















Reviews: