Better Water EQROPB01600 Operator'S Manual Download Page 68 | Manualshive

Page: 68 / 84

background image

Better Water LLC; rev. Jul 2019

Page 64 of 80

PB2

– Mediport Portable RO Operator Manual

TECHNICAL SERVICE BULLETIN

PB2 Water Quality Monitor Adjustment to Alarm on %-

Rejection for Nuisance Alarms

TSB#

TSB2012003

Date

04/27/12

Page 1 of 3

ISSUE

On occasion feed water quality changes for various reasons. This is sometimes due municipalities changing
water sources, modifying pretreatment, or construction and repair to main water lines.  These can cause
erratic feed TDS changes and fluctuating pH.

The PB2 is set at the factory to alarm on %-Rejection.  In this setting the water quality is more prone to a
nuisance alarm due to the above mentioned changes in feed water quality.  The PB2 can alternately be set
to allow the alarm set-point to be set on Product TDS instead of %-Rejection.

SOLUTION

PRE-CHANGE VERIFICATION

1.

Verify the feed and product TDS values displayed on the Water Quality Monitor with a hand-held TDS

meter.

- If out of calibration see the Operators Manual for the calibration procedure. This manual is available online
and can be downloaded from

www.betterwater.com/support

.

DIPSWITCH CHANGE

1.

Turn the device

OFF

.

2.

Unplug from the electrical receptacle

3.

Open the

External Top Panel

and the

remove the cover from the internal

Control

Box

and locate the control board containing

the…

… block of two

Dipswitches

…

…the

CAL-UP

and

CAL-DOWN buttons

View from

the BACK of

the PB2

WARNING

1. ELECTRICAL HAZARD: Be careful where and what is touched when making the changes
described below inside the internal control box.

2. The following changes should not be done while a hemodialysis treatment is being performed.

«
...
66
67
68
69
70
...
»

Summary of Contents for EQROPB01600





















































































Reviews:

No comments

Related manuals for EQROPB01600

Brand: Lavit Pages: 59

Brand: A.O. Smith Pages: 6

Brand: Precision Pages: 15

Brand: Western Shelter Systems Pages: 2

Brand: Laars Pages: 20

Solar Storage Tank Water Heater

Brand: American Water Heater Pages: 15

Brand: Cipax Pages: 10

Brand: K-Tec Pages: 24

Brand: Grindmaster Pages: 2

Brand: Grindmaster Pages: 2

Brand: Grindmaster Pages: 36

Brand: Kenmore Pages: 28

Brand: Kenmore Pages: 28

Brand: FCI Pages: 16

Brand: Nature's Comfort Pages: 6

Brand: Modena Pages: 9

Brand: IRIT Pages: 2

Brand: Duprex Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands