Better Water EQROPB01600 Operator'S Manual Download Page 74 | Manualshive

Page: 74 / 84

background image

Better Water LLC; rev. Jul 2019

Page 70 of 80

PB2

– Mediport Portable RO Operator Manual

TECHNICAL SERVICE BULLETIN

PB2 Bypass for Using External Nephros SSU Filter

TSB#

TSB2012008

Date

10/15/12

Page 1 of 1

OVERVIEW:

The PB2 (portable RO) comes standard with an internal .05 micron Pyrogen filter. Better
Water has created a simple solution for those customers who have expressed an interest
in using an external Nephros SSU Pyrogen capsule filter. This solution involves the
removal of the standard internal .05 micron Pyrogen filter and replacing it with a bypass
tube with quick-connect ends.

This bypass tube, part#

EQSUBPB2FT

is available from Better Water.

USE of the NEPHROS SSU CAPSULE FILTER:

When using the Nephros SSU capsule filter, it should be installed on the product hose between the PB2 and
the dialysis machine. A sample port should also be installed after this filter to draw water to mix bicarb and
for bacteria sampling,

REPLACEMENT INSTRUCTIONS:

1. Turn the power to the RO unit OFF.

2. Turn the water supply to the RO unit OFF.

3. Open the lab-cock, located inside the RO cabinet, and relieve filter-in and filter-out pressure. It is

advisable to use a small piece of tubing on the nipple of the lab-cock to route the draining water out of the

cabinet.

4. Close the lab-cock once the drain is complete.

5. Remove the .05 micron filter (

refer to the PB2 Operator Manual for instructions on how to remove the

filter

)

6. Attach the false/bypass tube in place of the filter. The connections will only allow it to be installed one

way.

7. Turn the water supply to the RO unit ON.

8. Open the lab-cock and allow water to flow until all air is purged. It is advisable to use a small piece of

tubing on the nipple of the lab-cock to route the draining water out of the cabinet.

9. Close the lab-cock once all the air is purged.

10. Install the Nephros SSU capsule filter on the product hose coming from the PB2.

11. Install a sample port after the Nephros SSU capsule filter.

12. The unit is now ready to run.

PB2 .05 False Tube

part# EQSUBPB2FT

Nephros SSU Pyrogen

Capsule Filter

NOTE

Better Water LLC recommends that one of these two filters must

be used with the PB2 to ensure water quality.

«
...
72
73
74
75
76
...
»

Summary of Contents for EQROPB01600





















































































Reviews:

No comments

Related manuals for EQROPB01600

Brand: Garantia Pages: 2

SBC 1100 ADV PLUS FR

Brand: Quick Pages: 76

Brand: hajdu Pages: 132

Brand: Santon Pages: 20

Bottled Water Dispenser Plus

Brand: FLOJET Pages: 16

Brand: Giant Factories Pages: 32

Brand: Taylex Pages: 17

Brand: Raypak Pages: 44

Brand: Water Well Pages: 5

HousePure HP-Soft-2

Brand: Water Pages: 18

Brand: Lacava Pages: 10

Brand: VOCO Pages: 169

Specialty Dispensers 1-12

Brand: Star Manufacturing Pages: 2

Peristaltic Heated Condiment Dispenser HPDE1

Brand: Star Manufacturing Pages: 2

Peristaltic Heated Condiment Dispensers SPDE1HP

Brand: Star Manufacturing Pages: 2

Brand: Star Manufacturing Pages: 2

Brand: Lancaster Pages: 14

Brand: EemaX Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands