2. After any required adjustments described in your tractor operator’s manual are made to the 3
point hitch on the tractor, hook up the applicator to the tractor. Raise parking stands to storage
position. While parked on level ground, level the sprayer by adjusting the 3-point top link.
3. Attach quick disconnect fittings to ends of hydraulic hoses to match tractor ports. Then con-
nect hydraulic hoses to tractor ports in a sequence that is both familiar and comfortable to the
operator. It is suggested that the hydraulic hoses for the hydraulic pump be connected to the num-
ber one outlet, while the boom control hoses are connected to the number two outlet or to the outlet
that corresponds to the outermost control lever on the tractor’s hydraulic control console. A low
pressure return port for the hydraulic pump is recommended.
4. If equipped with a Raven spray controller unit
(shown on next page
), install it in the tractor
cab, following the instructions provided with the controller unit. If an alternative brand of con-
troller is being used, install according to the manufacturer’s instructions.
5. Extend the controller power cable from the tractor cab to the battery and connect the battery
terminal rings directly to the battery posts, making sure
the positive (red) and negative (white)
wires correspond with the polarity of the battery terminals.
C2
IMPORTANT:
Damage may occur to this equipment if you fail to
raise the parking stands before operation!
IMPORTANT:
Always clean hose ends to remove any dirt before
connecting couplers to tractor ports
Before applying pressure to the hydraulic system,
make sure all connections are tight and that hoses
and fittings have not been damaged. Hydraulic fluid escaping under pressure can
have sufficient force to penetrate skin, causing injury and/or infection.
WARNING:
!
Summary of Contents for PRO-MOUNT 360
