background image

P29 - 54722 - Rev. I 0213

Installation Instructions - Supertop NX

© 2013 Bestop, Inc.

Installation Instructions

Supertop NX

Vehicle Application:

Jeep Wrangler

2007-current

Part Number 54722

Care and Maintenance of your Bestop Product

Your Bestop product is made of the finest materials available. To keep it looking new and for the maximum possible wear, it will need periodic cleaning and maintenance.

Fabric:

 The fabric should be washed often using soap, warm water and a soft bristle brush  Rinse with clear water to remove all traces of soap.  Bestop recommends using Bestop Cleaner 

(part no. 11201-00) and Bestop Protectant (part no. 11202-00) Bestop Cleaner and Bestop protectant are specially formulated to provide a total cleaning and protection system. Bestop Cleaner 

safely removes the toughest stains, will not harm vehicle finishes, is biodegradable and environmentally friendly.  Bestop Protectant protects against fading, cracking and hardening, and repels 

dust, grease, dirt and mildew.  

Windows:

 Keep windows clean to avoid scratching. DO NOT use a brush on the windows!  Wash with a water-soaked cloth or sponge

and a mild dishwashing detergent.  Bestop recommends Bestop Vinyl Window Cleaner (part no. 11203-00), which safely cleans and 

protects vinyl windows and helps prevent UV damage. NEVER WIPE THE WINDOWS WHEN THEY ARE DRY.

Be careful when cleaning snow or frost from the vinyl windows since they are easily scratched and may crack at low temperatures.

DO NOT roll the sides or rear window in cold weather.  The windows become stiff and will crack. Cracks caused by misuse in cold

temperatures are not covered under warranty. 

Zippers:

 Keeping zippers cleaned and lubricated with Bestop’s Zipper Cleaner (part no. 11206-00) will help prevent damage and keep the

zippers in smooth working condition.  If a zipper opens behind the slider, the slider may have been spread apart. This problem can usually

be repaired by using an ordinary pair of pliers to bring the sides back into parallel. Return slider to the end of the zipper in the normal Open

position.  Squeeze lightly at first and test the zipper. If the zipper continues to remain open squeeze more firmly with the pliers and try the

zipper again. Repeat this procedure until the zipper operates correctly.   

Water:

 Seeping through at the seams may be stopped by applying 3-M Scotchgard® on the inside of the seams. Rips in the fabric may be

repaired with Bondex® iron on patches. Iron the patches to the Inside of the top, carefully following the Bondex® instructions. 

Snaps:

 Keep snaps cleaned and lubricated with silicone to help prevent snaps from sticking to the studs. If a snap does become stuck

to a stud, use a screwdriver and GENTLY pry apart to prevent permanent damage to the snap or the top fabric.  

LIMITED WARRANTY

We warrant our product to be free from defects in material and workmanship, for the terms specified below, provided there has been normal use and proper maintenance. This warranty applies to the 

original purchaser only. All remedies under this warranty are limited to the repair or replacement of any item or items found by the factory to be defective within the time period specified. If you have 

a warranty claim, first you must call our factory at the number below for instructions.  You must retain proof of purchase and submit a copy with any items returned for warranty work. Upon completion 

of warranty work, if any, we will return the repaired or replaced item or items to you freight prepaid. Damage to our products caused by accidents, 

 re, vandalism, negligence, misinstallation, misuse, 

Acts of God, or by defective parts not manufactured by us, is not covered under this warranty.       
THE WARRANTY TIME PERIOD IS AS FOLLOWS FOR REPLACE-A-TOP™, SAILCLOTH REPLACE-A-TOP™, SUPERTOP®, SUPERTOP® REPLACEMENT SKINS, 

SUNRIDER®, AND TIGERTOP®: TWO YEARS FROM DATE OF PURCHASE.
THE WARRANTY TIME PERIOD IS AS FOLLOWS FOR ALL OTHER “SOFT GOODS” MANUFACTURED BY OUR COMPANY (USING PRIMARILY VINYLS, PLASTICS , AND/OR FOAM): 

ONE YEAR FROM DATE OF PURCHASE.
THE WARRANTY TIME PERIOD IS AS FOLLOWS FOR ALL OTHER “HARD GOODS” MANUFACTURED BY OUR COMPANY (USING PRIMARILY METALS, PLASTICS , 

AND/OR FIBERGLASS): ONE YEAR FROM DATE OF PURCHASE.
ANY  IMPLIED W ARRANTIES  OF MERCHANTABILITY AND/OR  FITNESS FOR  A  PARTICULAR  PURPOSE CREATED  HEREBY ARE  LIMITED IN DURATION  TO  THE  SAME

DURATION AND SCOPE AS THE EXPRESS WRITTEN WARRANTY. OUR COMPANY SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGE.   
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or con sequential damages, so the above limitations or exclusions may not apply 

to you. This warranty gives you speci

 c legal rights, and you may also have other rights which vary from state to state. 

For further information or request for warranty work, please contact:

Bestop Inc., Customer Service

Toll-Free: (800) 845-3567

Main: (303) 465-1755

E-mail: [email protected]

Website: www.Bestop.com

Damaged Slider - 

Jaws Spread Apart 

(sometimes broken)

Normal Slider - 

Jaws Parallel

Summary of Contents for Supertop NX

































Reviews: