BEST ACCESS SYSTEMS 9KQ Installation Instructions Manual Download Page 7

Page: 7 / 16

Installation Instructions for Wi-Q™ Technology 9KQ Cylindrical Locks

Installing the lock

BEST ACCESS SYSTEMS

a Product Group of dormakaba USA Inc.

Remove outside lever or knob

1 Insert the control key into the core and rotate the key

15 degrees to the right.

2 Insert a flat blade screwdriver into the figure-8 core

hole and into the lever.

3 Press the screwdriver blade in the direction of the

arrow in Figure 7.

Note: You cannot remove the lever if the screwdriver
blade is inserted too far past the keeper.

4 Slide the lever or knob off of the sleeve.

Caution:

Be careful that you do not disconnect the

lever keeper spring.

Adjust for door thickness

1 Determine the door’s thickness.

2 Pull the rose locking pin and rotate the outside rose

liner until the proper groove on the through-bolt stud
lines up with the hub face.

Figure-8
core hole

Figure 7

Removing the outside lever

Lever keeper

Insert screwdriver
blade here.

Figure 8

Adjusting the rose liner for the door
thickness

1 3/4

″

2 1/4

″

groove

Through-
bolt stud

Hub face

Outside
rose liner

Rose locking pin

Motor wire

Summary of Contents for 9KQ

















Search results

Summary of Contents for 9KQ

Reviews:

Related manuals for 9KQ

Brands by name

Popular brands

BEST ACCESS SYSTEMS 9KQ, Installation Instructions Manual

Search results

Summary of Contents for 9KQ

Reviews:

Related manuals for 9KQ

Brands by name

Popular brands