manualshive.com logo in svg

BEST ACCESS SYSTEMS 9KQ, Installation Instructions Manual

Share
Download
BEST ACCESS SYSTEMS 9KQ Installation Instructions Manual Download Page 14

Installation Instructions for Wi-Q™ Technology 9KQ Cylindrical Locks

14

Completing the installation

BEST ACCESS SYSTEMS

a Product Group of dormakaba USA Inc.

 Figure 20b Installing the top cover

20

Install top cover
(inside escutcheon)

1  Connect the antenna to its mating connector.

2  Place the top cover against the door and above the fire 

plate. Slide the top cover down toward the bottom 
cover as shown in Figure 20b.

Caution:  

As you slide the top cover onto the fire 

plate, feed the antenna wire down into the 
bottom cover. Be sure not to pinch the antenna 
wire on the bottom cover as you slide the top 
cover into place.

3  Use two cover screws to secure the cover to the side of 

the fire plate, as shown in Figure 20b.

Note: Phillips Type 2 and T20 Torx options are available 
for the cover mounting screws.

 Figure 20a Inside view of top cover

Top cover

Antenna wire

Top cover

Inside of door

Cover screws

Antenna wire

Summary of Contents for 9KQ

















Reviews:

No comments

Brands by name

Popular brands

Load more brands