manualshive.com logo in svg

Berthold 55393 BA2, Operating Manual

Share
Download
Berthold 55393 BA2 Operating Manual Download Page 21

LB 983 NightSHADE Operating Manual 

Quick Start 

 

21 

4.1.5  Connecting 

 
The power supply and device communication 
ports  are  located  on  the  rear  panel  of  the 
NightSHADE.  Plug  the  power  cord  into  the 
mains  inlet  (1).  The  main  power  switch  is  lo-
cated next to the mains inlet.  
Connect  the  NightSHADE  to  the  PC  via  the 
USB  B-socket  (2)  on  the  rear  panel  using  a 
USB cable (A to B). 
The  7-pin  Tuchel  socket  (4)  is  the  power 
supply for the side mounted camera, the USB 
socket  (3)  is  used  for  the  control  of  the  side 
view  camera  only.  The  residual  current  de-
vice  (RCD)  is  a  protection  device  and  cuts 
the supply voltage in case of any leakage current. 
 

The function of the RCD must be tested before each use. Therefore press the blue button 
with the “T” label and check if the safety device cuts the supply voltage. 

 

Check  to  make  sure  that  the  system  voltage  indicated  on  the  instruments  matches  the 
line voltage.

 

 
If possible connect all devices via 

one

 outlet strip to the mains supply

.

  

The NightSHADE is initialized after power on; a control lamp on the front panel is flashing. 
The NightSHADE camera is ready for operation after it has cooled down to operating tempera-
ture; this takes approximately 10 minutes. 
 

The  cooling  of  the  camera  is  initialized  when  the  indiGO  software  is  started  (controller 
statup).  Switching  on  the  NightSHADE  without  starting  the  software  will  not  cool  down 
the camera. 
 

 

4.1.6  Power On 

After  power  on, the  device  starts  an  automatic  initialization  where  all  relevant  components  will 
be initialized. During this time, the LED on the front panel is flashing red. After the successful in-
itialization the NightSHADE is ready for operation.  
 
The  indioGO  software  automatically  recognizes  the  NightSHADE.  No  further  steps  are  neces-
sary.  

 

 

 

I

0

1

2

3

T

5

4

Summary of Contents for 55393 BA2































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands