Bernina 820 Owner'S Manual Download Page 108

Page: 108 / 148

108

BSr (BernIna Stitch regulator) function

The BSR presser foot reacts to the movement of the fabric under the foot and controls the

speed of the sewing computer up to the maximum speed possible. The following applies:

the faster the fabric is moved the higher the speed of the sewing computer.

If the fabric is moved too fast an acoustic signal (beep) is heard, and the red light of the

Start-/Stop Button flashes. The beeper can be turned on or off in the Setup Program or

directly on the «BSR» screen.

BSr Description

By activating the BSr function the sewing

computer sews either continuously at a

reduced motor speed (mode 1, standard),

or as soon as the fabric is moved (mode 2).

as long as the BSr presser foot is illumi-

nated red, adjustments like threading and

changing the needle, for example must not

be carried out, as the needle will engage

while fabric is moved unintentionally!

Without fabric feed the BSr mode is

turned off after approx. 7 seconds and the

red light goes off.

please refer to the Safety Instructions!

When exceeding a certain speed, adhering to

regular stitch length cannot be guaranteed.

Make sure that the lens on the bottom of

the BSR foot is not dirty (fingerprints, etc.).

Clean lens periodically with soft, slightly

damp cloth.

For an even sewing start (one single stitch)

the foot control must be pressed and the fabric

moved simultaneously.

This also applies for sewing points and

straight stitching within a round form.

If the BSR function is deactivated and later

re-activated without the sewing computer

being switched off in between, the last

selected BSR mode is active.

With Straight Stitch no. 1

This function using a special presser foot allows for Free

Motion quilting (sewing) using the straight stitch and a

pre-selected stitch length (up to 4mm).

A regulated set stitch length is maintained within a certain

speed, independent of the movement of the fabric.

With Zigzag Stitch no. 2

The zigzag stitch can be used for thread painting or fabric

embellishment.

The set stitch length will

not

be maintained when sewing

with the zigzag stitch, but the BSR function simplifies

the application.

BSr function can be sewn in 2 separate

modes of operation

►

BSR mode 1 is the active standard

►

the sewing computer runs continuously at a reduced

motor speed, as soon as the foot control or the Start/

Stop Button is pressed

►

moving the fabric under the foot will engage the sewing

computer to accelerate

►

through the continuous needle movement securing in

the same position is possible without pressing an

additional button

►

touch the button «BSR2» to engage BSR mode 2

►

the sewing computer will only engage if the foot control

or the Start/Stop Button is pressed and the fabric is

moved simultaneously

►

the movement of the fabric determines the sewing

speed

►

for securing, the «Securing Function» button must be

pressed

►

touch the button «BSR1» to engage BSR mode 1

032298.53.04_1204_B820_EN

Summary of Contents for 820





















































































































































Search results

Summary of Contents for 820

Reviews:

Related manuals for 820

Brands by name

Popular brands

Bernina 820, Owner'S Manual

Search results

Summary of Contents for 820

Reviews:

Related manuals for 820

Brands by name

Popular brands