background image

-11-

PLUS

AUTO

Door opens:

 The air curtain and heater (if temperature is below thermostat setting)

activate and run at set speed.

Door shuts:  

The air curtain turns off after the time delay expires. If thermostat is not

satisfied, air curtain and heater continue to run until the thermostat is satisfied.  If the

thermostat drops below set temperature, the heater and air curtain will activate and run

on a low speed until the thermostat is satisfied.

Door opens:

 The air curtain activates.

Door shuts: 

The air curtain turns off, after time delay expires.

Door opens:

 The air curtain activates immediately when mode is selected.

Door shuts: 

The air curtain continues to run.  

Door opens:

 The air curtain is off.

Door shuts: 

The air curtain is off.

OFF

Standard Mode of Operation Options:

STEP THREE

Once the

 Mode of Operation

 is selected, press the           button. 

For heated units only

STEP ONE

To Start:

 Press the down arrow button once.

NOTE:  To change from “Mode” to “Fan Speed” press the down arrow twice.

STEP TWO

Use the                     buttons to scroll through the available modes of operations.

ON

Customizable Mode of Operation Options:

See 

www.berner.com/intelliswitch

 for programming directions

(Section 5, Program Menu).

  

www.berner.com

    

Berner International   

800.245.4455

 

111 Progress Ave. / New Castle / PA / 16101 / USA

+

+

Summary of Contents for AE08

















Reviews: