BERGHOF ET2115 User Handbook Manual Download Page 28 | Manualshive

Page: 28 / 48

background image

USER HANDBOOK 1.0 | ET2115

Berghof Automation GmbH | Harretstrasse 1 | 72800 Eningen | www.berghof.com

21-0099-82-00-00-003 |222002100_Anwenderhandbuch_Ethernet-Terminal-ET2115_EN.docx

28

6.3.2. Function key S1

Fig. 18: Function key (S1)

The function key S1 is for use only by Berghof Service staff.

6.3.3. microSD card

WARNING

Serious injury as a result of uncontrolled and unpredictable operational
behaviour!

Inserting or removing the microSD card can result in the device malfunctioning.
Failure in electronic control systems may result in uncontrolled and
unpredictable operational behaviour.



Insert or remove a microSD card only when the device is switched off.

NOTE

Loss of data!

microSD cards do not have their own write protection system.



Ensure that no data is deleted or overwritten by accident.

The microSD card slot is for use only by Berghof Service staff.

«
...
26
27
28
29
30
...
»

Summary of Contents for ET2115

















































Reviews:

No comments

Related manuals for ET2115

Brand: S&C Pages: 40

Brand: Zeagle Pages: 37

Brand: Galaxy Control Systems Pages: 5

Brand: Häfele Pages: 2

Brand: Häfele Pages: 24

Brand: Veeder-Root Pages: 27

Brand: Valve Concepts Pages: 18

Brand: K&K Pages: 6

Pulsafeeder MPC Vector

Brand: Idex Pages: 114

RDS17S-ELITE1-R1

Brand: D&R ELECTRONICS Pages: 12

iDual A E27 iD60

Brand: jedi LIGHTING Pages: 23

Brand: Cypress Pages: 3

IB-TRON 4000 SOL

Brand: INSBUD Pages: 14

Brand: babyplus Pages: 28

Brand: GCE Pages: 13

Brand: Leviton Pages: 2

Brand: TECH Pages: 20

Brand: Flying Industry Development Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands