BERGHOF ET2115 User Handbook Manual Download Page 16 | Manualshive

Page: 16 / 48

background image

USER HANDBOOK 1.0 | ET2115

Berghof Automation GmbH | Harretstrasse 1 | 72800 Eningen | www.berghof.com

21-0099-82-00-00-003 |222002100_Anwenderhandbuch_Ethernet-Terminal-ET2115_EN.docx

16

4.2. Installation

Fig. 4: Insertion into the installation cut-out

Requirements:



The securing clips must not be attached to the device.

1.

Making sure the alignment is correct, push the device evenly into the installation cut-out.

NOTE

Damage to the device!

If installation is performed carelessly the device can fall out of the installation
cut-out or be damaged.



Do not tilt the device.



Restrain the device against falling until the securing clips have been
secured.

«
...
14
15
16
17
18
...
»

Summary of Contents for ET2115

















































Reviews:

No comments

Related manuals for ET2115

Brand: NEJE Pages: 17

Brand: Oceanic Pages: 13

Brand: Waterway Pages: 16

Brand: Panasonic Pages: 45

medialon Showmaster Go

Brand: 7th Sense Pages: 2

Brand: CAME Pages: 18

Brand: CAME Pages: 28

Brand: CAME Pages: 28

Brand: CAME Pages: 4

Brand: CAME Pages: 40

Brand: CAME Pages: 26

Brand: CAME Pages: 34

Brand: CAME Pages: 2

Brand: Daikin Pages: 5

Brand: Lawler Pages: 6

Brand: Data Aire Pages: 28

Brand: Samson Pages: 32

Brand: Quantum Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands