background image

171 505 46  09-01

Two pipe installation

One pipe installation

Oil under

pressure

Oil under 

suction

By-passed 

oil returned 

to tank,or 

to suction

INSTRUCTIONS PUMP TYPE SUNTEC A2L 65C  -  75C

Pump operating principle for

A2L 65C  -  75C

The 

SUNTEC A2L

 oil pump has two 

nozzle outlets. It incorporates two 

blocking solenoid valves with in-line-

cut-off function, one for each nozzle 

outlet.

The gear set draws oil from the tank 

through the built-in fi lter and transfers 

it to the nozzle line via the cut-off so-

lenoid valves. A pressure regulating 

valve is used to dump all oil which is 

not required at the nozzle.

In one-pipe operation, the oil which 

does not go through the nozzle lines is 

returned directly to the gear inlet and 

the suction line fl ow is equal to the 

sum of the 2 nozzle fl ows. In two-pipe 

operation, the by-pass plug must be 

fi tted in the return port, which ensures  

that the oil dumped by the regulating 

valve is returned to the tank and the 

suction line fl ow is equal to the gear 

set capacity.

Bleed

Bleeding in two-pipe operation is au-

tomatic: it is assured by a bleed fl at 

on the piston. In one-pipe operation, 

a high pressure connection must be 

loosened until the air is evacuated 

from the system.

Cut-Off

The solenoid valves of the A2L pump 

are of the "normally closed" type and 

are situated in the nozzle lines. This 

design ensures extremely fast res-

ponse and the switching can be sel-

ected according to the burner opera-

ting sequence and is independant of 

motor speed.

When the solenoids are non-activated, 

the valves are closed and all oil 

pressurised by the gear set passes 

through the regulator to suction or to 

the return line, depending upon pipe 

arrangement.

As soon as the solenoids are activat-

ed, oil passes to the nozzle lines at 

the pressure set by the pressure 

regulating valve.

A2L

 C

XX

Shaft rotation and nozzle

location seen from shaft end 

Gear set capacity

A2L: 2 nozzle outlets

Exchange of fi lter

Mounting/dismounting return plug

One pipe system

Two pipe system

Solenoid valve 2 (NC) closed

Solenoid valve 2 

(NC) open

Solenoid valve 1 

(NC) open

To nozzle 2

To nozzle 1

Pressure 

gauge port

Pressure 

gauge port

Shaft seal

By-pass 

plug

Return

Suction

By-pass plug

removed

Solenoid valve 1 (NC) closed

Gear set

Vacuum gauge port

 Pressure adjustment

Return 

plugged

Back to suction

Summary of Contents for B30A2.2H





















Reviews: