Benthos 865-A Instructions For The Installation, Operation And Maintenance Download Page 39 | Manualshive

Page: 39 / 68

background image

Model 865-A Deep Sea Acoustic Release/Transponder

M-855-009

Benthos, Inc.

31

d.

Now send several single transponds on the proper code and verify that five replies occur from
the 865-A with each transpond.

STEP 7 - PREPARE FOR DEPLOYMENT

At this point, the 865-A is ready for installation into the mooring or other appropriate hardware.

a.

With the release pin retracted, install the Benthos stainless steel expendable release link, then
turn the switch to HOLD-EXTEND. Be careful to avoid jamming the pin.

b.

When the pin has fully extended, turn the switch to ON- ARMED. Listen for power-up pings.

c.

Check that the white plastic inserts on each end of the 865-A are not damaged to reduce the
possibility of corrosion problems.

The 865-A is now ready for deployment.

«
...
37
38
39
40
41
...
»

Summary of Contents for 865-A





































































Reviews:

No comments

Related manuals for 865-A

Brand: Icom Pages: 27

Brand: Icom Pages: 72

Brand: Uflex Pages: 16

RSM-WSB(RED)-AS

Brand: Hochiki Pages: 2

Brand: Blaupunkt Pages: 56

Brand: True Heading Pages: 43

Brand: Campbell Pages: 51

Brand: Manta Pages: 16

Brand: SANG Pages: 20

Brand: Eurochron Pages: 8

Brand: MAJORITY Pages: 112

Brand: Navico Pages: 9

Brand: Emerson Pages: 4

Brand: Kongsberg Pages: 74

Brand: Garmin Pages: 62

Brand: Vertex Standard Pages: 40

Brand: Kenwood Pages: 2

Brand: Kenwood Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands