Benthos 865-A Instructions For The Installation, Operation And Maintenance Download Page 16 | Manualshive

Page: 16 / 68

background image

Model 865-A Deep Sea Acoustic Release/Transponder

M-855-009

Benthos, Inc.

8

3.0

SPECIFICATIONS

3.1

Electrical

3.1.1

Power Source

3.1.1.1

Standard Battery Pack

18 alkaline 'D' cells to provide two strings at a nominal 13.5 volts (Benthos P/N 865-SB-13).
Capacity: 22 Amp-hours (de-rated for cold temperature use and two year deployment time)

3.1.2

Operating Life

3.1.2.1

Standard Battery Pack

Release after 2 years and 250,000 transponds.

3.1.3

Acoustic Output

Greater than 192 dB re 1 micropascal at 1 meter from 9.0 to 16.0 kHz.
Greater than 185 dB from 7.5 to 8.5 kHz.

3.1.4

Receive Frequency

The receiver frequency is factory set to any one frequency between 7.0 kHz and 15.0 kHz in 500 Hz
increments (12.5 Khz is reserved and not used as a standard receive frequency). The receiver
bandwidth is ± 125 Hz.

All of the above frequencies are transmitted as standard by the DS-7000 deck unit.

3.1.5

Transmit Frequency

User selectable 7.5 to 17.0 kHz in 250 Hz increments.

3.1.6

Transmit Pulse Width

10 ms ±1 ms.

3.1.7

Command Channels

«
...
14
15
16
17
18
...
»

Summary of Contents for 865-A





































































Reviews:

No comments

Related manuals for 865-A

Brand: Raymarine Pages: 464

Brand: Radwin Pages: 252

Brand: Radwin Pages: 6

Brand: Magnavox Pages: 2

Brand: Magnavox Pages: 13

Brand: Magnavox Pages: 14

Brand: Magnavox Pages: 14

Brand: Quick Pages: 24

Brand: Raytheon Pages: 68

Xpress XMCK-20KC

Brand: Audiovox Pages: 2

Brand: Sangean Pages: 78

Zlinx ZP24D-250RM-SR

Brand: B&B Electronics Pages: 2

Brand: SBO Hearing Pages: 4

Brand: Konig Pages: 21

Brand: Coby Pages: 1

Brand: Sirius Satellite Radio Pages: 36

Brand: Centrios Pages: 23

Brand: Belkin Pages: 102

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands