D-304957 BW-ODT Installation Instructions
3
Important:
Reliable reception must be assured. Therefore, "poor" signal strength is not acceptable. If you receive a "poor" signal from the
detector, relocate it and re-test until a "Good" or "Strong" signal strength is received.
Note:
For detailed Diagnostics Test instructions refer to the control panel Installer's Guide.
The LED blinking, described above, is operative only in Local diagnostic mode. Upon each full detection (LED lights steadily for 2 seconds),
the control panel receives the alarm. If required, perform the detector's horizontal / vertical adjustments (see section 2.1 and Figure 3).
Important:
Instruct the user to perform a walk test at least once a week, to verify proper operation of the detector.
D.
Place a piece of cardboard on the detector’s front side to deliberately mask the optical window. Verify that after 2 minutes, the yellow LED lights
continuously (see Table 3 below) and the alarm control panel receives the masking alarm.
E.
Remove the masking from the detector’s front side. Verify that the LED turns off.
Table 3 - LED operation
LED Indications
Event
Red LED blinks
Stabilization (warm-up 60 sec)
Red LED ON 0.2 sec.
Tamper open / close
Red LED blinks twice
One quad PIR detection in diagnostic mode
Red LED ON 2 sec.
Intruder alarm
Yellow LED ON
AM detection – diagnostic mode
Yellow LED blinks slowly (0.2 sec. ON, 30 sec. OFF)
AM detection – Normal mode
3. COMPLIANCE WITH STANDARDS
Europe:
EN 300220, EN 301489, EN 62368-1, EN 60950-22, EN 50130-4, EN 50130-5, EN 50131-2-2, EN 50131-5-3, EN 50131-6
Type C.
Hereby, Bentel Security S.r.l. declares that the radio equipment type BW-ODT is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address:
Certified by Norwegian accredited certification body Applica Test & Certification AS in accordance with EN 50131-2-2, EN
50131-5-3, EN 50131-6, EN 50130-4, and EN 50130-5.
UK
: This product is suitable for use in systems installed to conform to PD6662 at Grade 2 and environmental class IV.
BS8243
W.E.E.E. Product Recycling Declaration
For information regarding the recycling of this product you must contact the company from which you originally purchased it. If you
are discarding this product and not returning it for repair then you must ensure that it is returned as identified by your supplier. This
product is not to be thrown away with everyday waste.
Directive 2012/96/EC Waste Electrical and Electronic Equipment.
APPENDIX: SPECIFICATIONS
OPTICAL
Black Mirror Max. Coverage
Up to 12 m (40 ft) / 90°
Detector Technology
8 independent quad PIR detectors operating in true Quad configuration
(See figure. 6)
Pet Immunity
Up to 18 Kg (40 lb)
ELECTRICAL
Input Power
Two 3V CR123A Lithium batteries
Caution!
Risk of explosion if battery is replaced by an incorrect type. Dispose of used battery according
to the manufacturer's instructions.
Battery Life (for typical use)
3 years
Low Battery Threshold
4.0 V
Operation voltage
4 V to 6.6 V
Current consumption
25 uA to 150 mA
WIRELESS
Frequency Band (MHz)
868-869
Maximum Tx Power
14 dBm @ 868 Mhz
Communication Protocol
PowerG
Tamper Alert
Reported when a tamper event occurs and in any subsequent message, until the tamper switch is restored
MOUNTING
Mounting Type
Wall mounting
Mounting Height
1.5 – 3.0 m (5 – 10 ft)
Horizontal Adjustment
-45° to +45°, in 5° steps
Vertical Adjustment
0° to -10°, in 2.5° steps
ENVIRONMENTAL
Operating Temperatures
-35°C to 60°C (-31°F to 140°F)
Storage Temperatures
-35°C to 60°C (-31°F to 140°F)
Humidity
95% max.
White Light Immunity
Above 25000 lux
PHYSICAL
Size (H x L x W)
157 x 147 x 124 mm (6-3/16 x 5-13/16 x 4-7/8”)
Weight (with battery)
600 g (21 oz)
Color
White
PATENTS
U.S. Patents 7250605
6818881
5693943 (other patents pending)
