12
9.3 Power Connector
IEC-06
10.0 Panel Specification
10.1 Type
Single Chip 0.55” SVGA 12
°
tilt DDR DMD
10.2 Pixels
H: 800 X V: 600
10.3 Color Depth
24 Bits (16770000 colors)
11.0 Compatibility
Appendix E3
11.1 PC
PC Compatible 640X480
Æ
1024X768, compressed 1280X1024;
Composite-Sync; Sync-on-Green; Interlace Mode (8514A);
11.2 Video
NTSC/ NTSC4.43/ PAL (Including PAL-M, PAL-N)/ SECAM/
PAL60/
11.3 YpbPr
NTSC (480i)/ 480p/ PAL (576i)/ 576p, HDTV (720p/ 1080i)
11.4 DDC
DDC 2B
12.0 Image Interface
Adhere to Appendix E.2
12.1 Analog RGB Input
15 pin D-Sub (Female) x 1
G(Y): Video amplitude 0.7/1.0 Vp-p : Impedance 75
RB(CbCr): Video amplitude 0.7 Vp-p : Impedance 75
HD/VD/CS: TTL Level
12.2 Video Input
RCA jack (Yellow)
Video amplitude 1.0 V
p-p
: Impedance 75
Ω
12.3 S-Video Input
4 pin Mini-Din (Female)
Y: Luminance amplitude 1.0 V
p-p
: Impedance
75
Ω
C: Chroma amplitude 0.268 V
p-p
: Impedance
75
Ω
12.4 YPbPr Input
15 pin D-Sub (Female) x 1
Y: Luminance amplitude
1.0 V
p-p
: Impedance 75
Ω
PbPr/C
b
C
r
: Chroma amplitude 0.7 V
p-p
: Impedance 75
Ω
12.5 Analog RGB Output
15 pin D-Sub (Female) x 1
G(Y): Video amplitude 0.7/1.0 Vp-p : Impedance 75
RB(CbCr): Video amplitude 0.7 Vp-p : Impedance 75
HD/VD/CS: TTL Level
13.0 Control Interface
13.1 IR Receiver
IR Receiver x2 (Front, Rear) Angle: ±15
°
Distance 0~8m
13.2 Serial Connector
RS232 8pin Mini DIN
13.3 USB Connector
B Type USB Terminal for page up/down
14.0 User Interface
Adhere to Appendix E.3
14.1 Operator Keypad
9 Keys:
Power ; Source ; Auto ; Blank/Q? ; Preset ; Left; Right ; Up ;
Down(Menu) ; Mode
Summary of Contents for Mainstream MP611
