14
OPENING AND CLOSING MOVEMENT SPEED ADJUSTMENT
You can adjust the opening and closing movement speed following this procedure (the slowing speed remains unchanged):
Switch DIP 1 and DIP 2 ON.
with the PU1 key, select the CLOSURE speed, indicated by LED LD3
LD3 1 flashing
50% of maximum speed (Default)
LD3 2 flashes
75% of maximum speed
LD3 steady light
maximum speed
with the PU2 key, select the OPENING speed, indicated by LED LD1
LD1 1 flashing
50% of maximum speed
LD1 2 flashes
75% of maximum speed
LD1 steady light
maximum speed (Default)
ATTENTION: Switch DIP 1 and 2 OFF at the end of programming.
There is a label applied inside the central cover with the table in Fig. 2 which schematically summarises the functions described above.
OPERATOR PRESENT MODE
Switching DIP to ON changes the control unit to OPERATOR PRESENT mode.
The PHOT input takes on the CLOSE key function (connect key with N.O. contact).
The S.S. input takes on the OPEN key function (connect key with N.O. contact).
The OPEN/CLOSE keys must remain pressed during the movement.
Opening the STOP input stops the motor. Simultaneous pressing of OPEN/CLOSE keys stops the motor.
CONFIGURATION OF BUILT-IN RECEIVER
(MANUAL STORAGE)
The control unit is equipped with a built-in radio module to receive ARC rolling-code remote controls, with a frequency of 433.92MHz.
Before using the remote control, please study the information with care, the storage procedure is shown as follows, the device is able to store up to 64
different codes.
Storage of a transmitter key with S.S. activation
- Press the PU2 key once for 1s, the LD1 LED emits 1 flash with 1s pause.
- Press the key of the transmitter to be memorised with S.S. function within 10s, the 3 red LEDs light up for 1s, then, after storing, the receiver auto-
matically exits the programming phase.
Storage of a transmitter key with SECOND RADIO CHANNEL function enabling.
- Press the PU2 key once for 1s, the LD1 LED emits 1 flash with 1s pause.
- Press the PU2 key again, the LD1 LED flashes twice with 1s pause
- Press the key of the transmitter to be memorised the 2nd Radio Channel within 10s, the 3 red LEDs light up for 1s, then, after storing, the receiver
automatically exits the programming phase.
The output enables for 1 second on each press of the memorised key.
To exit programming without storing the transmitter, wait 10s.
Storage of a transmitter key with PEDESTRIAN function enabling
- Press the PU2 key once for 1s, the LD1 LED emits 1 flash with 1s pause.
- Press the PU2 key twice more, the LD1 LED will flash 3 times with 1s pause
- Press the key of the transmitter to be memorised with the Pedestrian function within 10s, the 3 red LEDs light up for 1s, then, after storing, the
receiver automatically exits the programming phase.
Pressing the key associated with the pedestrian function controls partial opening of the leaf (approx. 1.5m)
Deletion of a radio code
- Press the PU2 key once for 1s, the LD1 LED emits 1 flash with 1s pause.
- Press the PU2 key again 3 times, the LD1 LED will flash 4 times with 1s pause
- Press the key of the transmitter you want to delete within 10s, the 3 red LEDs light up for 1s, then, after deletion the receiver automatically exits the
programming phase.
Remote acquisition of a transmitter
If you already have a memorised transmitter, others can be memorised without accessing the control panel. Remote storage must be performed with
the panel completely open, regardless of the TCA setting. Proceed as follows:
1 Press the hidden key on the previously memorised transmitter.
2 Press the key of the memorised transmitter to be copied within 10s. The flashing light switches on to conform receipt.
3 Press the hidden key of the new transmitter to which the function is to be associated within 10s.
4 Press the key of the new transmitter to which you want to associate the function selected in point 2 within 10s. The flashing light switches on to
conform receipt.
5 The new transmitter has been memorised, the receiver exits the programming phase.
E.g.: key 1 of TX “A” contains the S.S. function that you want to assign to key 2 of the new TX “B”; press in sequence:
hidden key of TX A >> key 1 of TX A >> hidden key of TX B >> key 2 of TX B.
Deleting all transmitters from memory
- Keep the PU2 key pressed for 15s, the LD1 / 2/3 LEDs and the service light start flashing quickly and turn off when cancellation is complete.
- Release the PU2 key, the memory has been erased.
PLEASE NOTE:
Transmitters may not be memorised during the opening/closing phases of the motor due to safety reasons.
KNX COMMUNICATION INTERFACE
Today, KNX is the open global standard, compliant with the main European and international standards, allowing the automated and decentralized
management of technological systems of a wide range of structures: commercial buildings, industries, offices, homes, public premises, schools and
many more.
This product is compatible with KNX standard and can be connected to a KNX network using the optional X.BE accessory.
For further information, please refer to the instructions supplied with the X.BE.
